ASTM D 7110 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determining the Viscosity-Temperature Relationship of Used and Soot-Containing Engine Oils at Low Temperatures
Hardcopy , PDF
19-06-2020
English
01-12-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers how to measure the apparent viscosity of used and soot-containing engine oils at low temperatures.
1.2A shear rate of approximately 0.2 s-1 is produced at shear stresses below 200 Pa. Apparent viscosity is measured continuously as the sample is cooled at a rate of 3 °C per hour over the range of −5 °C to −40 °C.
1.3The measurements resulting from this test method are viscosity, the maximum rate of viscosity increase (Gelation Index) and the temperature at which the Gelation Index occurs.
1.4Applicability to petroleum products other than engine oils has not been determined in preparing this test method.
1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 8185 : 2018 | Standard Guide for In-Service Lubricant Viscosity Measurement |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4684 : 2002 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 3829 : 2002 : R2007 | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM D 4057 : 1995 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 3829 : 2020 | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM D 3829 : 2017 | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM D 4684 : 2008 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4684 : 2020 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 3829 : 2018 | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4684 : 2007 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4684 : 2017 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4684 : 2012 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 3829 : 2012 | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4684 : 2014 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 3829 : 2002 | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM D 4684 : 2002 : REV A | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4684 : 2007 : EDT 1 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4684 : 1999 : EDT 1 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4684 : 2017 : REV A | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 3829 : 2014 | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM D 3829 : 1993 : R1998 | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM D 4684 : 2018 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.