ASTM D 7049 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Metalworking Fluid Aerosol in Workplace Atmospheres
Hardcopy , PDF
14-03-2024
English
03-11-2023
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 34
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers a procedure for the determination of both total collected particulate matter and extractable mass metalworking fluid aerosol concentrations in the range of 0.07 to 5 mg/m3 in workplace atmospheres.
1.2This test method describes a standardized means of collecting worker exposure information that can be compared to existing exposure databases, using a test method that is also more specific to metal removal fluids.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 2523 : 2013 : R2018 | Standard Terminology for Metalworking Fluids and Operations |
| ASTM E 2148 : 2021 | Standard Guide for Using Documents Related to Metalworking or Metal Removal Fluid Health and Safety |
| ASTM E 1497 : 2023 | Standard Practice for Selection and Safe Use of Water-Miscible and Straight Oil Metal Removal Fluids |
| ASTM E 2889 : 2023 | Standard Practice for Control of Respiratory Hazards in the Metal Removal Fluid Environment |
| ASTM E 2523 : 2023 | Standard Terminology for Metalworking Fluids and Operations |
| ASTM E 1497 : 2017 | Standard Practice for Selection and Safe Use of Water-Miscible and Straight Oil Metal Removal Fluids |
| ASTM E 2148 : 2016 | Standard Guide for Using Documents Related to Metalworking or Metal Removal Fluid Health and Safety |
| ASTM E 2889 : 2012 : R2017 | Standard Practice for Control of Respiratory Hazards in the Metal Removal Fluid Environment |
| ASTM D 4840 : 1999 : R2018 : EDT 1 | Standard Guide for Sample Chain-of-Custody Procedures |
| ASTM D 3195 : 1990 : R2004 | Standard Practice for Rotameter Calibration |
| ASTM D 4532 : 2015 | Standard Test Method for Respirable Dust in Workplace Atmospheres Using Cyclone Samplers |
| ASTM D 4840 : 1999 | Standard Guide for Sampling Chain-of-Custody Procedures |
| ASTM D 1356 : 2015 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2017 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5337 : 2023 | Standard Practice for Setting and Verifying the Flow Rate of Personal Sampling Pumps |
| ASTM D 1356 : 2015 : REV B | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5337 : 2011 : R2016 | Standard Practice for Flow Rate Adjustment of Personal Sampling Pumps |
| ASTM D 1356 : 2014 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5337 : 1997 | Standard Practice for Flow Rate for Calibration of Personal Sampling Pumps |
| ASTM D 1356 : 2015 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2005 : R2010 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 4532 : 1997 | Standard Test Method for Respirable Dust in Workplace Atmospheres |
| ASTM D 1356 : 2020 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2000 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5337 : 2011 | Standard Practice for Flow Rate for Calibration of Personal Sampling Pumps |
| ASTM D 4532 : 2010 | Standard Test Method for Respirable Dust in Workplace Atmospheres Using Cyclone Samplers |
| ASTM D 4532 : 2022 | Standard Test Method for Respirable Dust in Workplace Atmospheres Using Cyclone Samplers |
| ASTM D 1356 : 2014 : REV B | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2014 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5337 : 2004 | Standard Practice for Flow Rate for Calibration of Personal Sampling Pumps |
| ASTM D 1356 : 2005 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 3195 : 1990 : R1998 : EDT 1 | Standard Practice for Rotameter Calibration |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.