ASTM D 665 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
Hardcopy , PDF
17-01-2024
English
03-01-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the evaluation of the ability of inhibited mineral oils, particularly steam-turbine oils, to aid in preventing the rusting of ferrous parts should water become mixed with the oil. This test method is also used for testing other oils, such as hydraulic oils and circulating oils. Provision is made in the procedure for testing heavier-than-water fluids.
Note 1:For synthetic fluids, such as phosphate ester types, the plastic holder and beaker cover should be made of chemically resistant material suitable for the type of fluid tested.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 7.4 – 7.6.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6138 : 2023 : REV A | Standard Test Method for Determination of Corrosion-Preventive Properties of Lubricating Greases Under Dynamic Wet Conditions (Emcor Test) |
| ASTM D 6158 : 2023 | Standard Specification for Mineral Hydraulic Oils |
| ASTM D 7577 : 2012 : R2021 | Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends |
| ASTM D 3603 : 2020 | Standard Test Method for Rust-Preventing Characteristics of Steam Turbine Oil in the Presence of Water (Horizontal Disk Method) |
| ASTM D 7548 : 2022 | Standard Test Method for Determination of Accelerated Iron Corrosion in Petroleum Products |
| ASTM D 8324 : 2021 | Standard Guide for Selection of Environmentally Acceptable Lubricants for the U.S. Environmental Protection Agency (EPA) Vessel General Permit |
| ASTM D 8181 : 2019 | Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils |
| ASTM D 1401 : 2021 | Standard Test Method for Water Separability of Petroleum Oils and Synthetic Fluids |
| ASTM G 205 : 2023 | Standard Guide for Determining Emulsion Properties, Wetting Behavior, and Corrosion-Inhibitory Properties of Crude Oils |
| ASTM D 4304 : 2022 | Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines |
| ASTM D 4007 : 2022 | Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 7973 : 2019 | Standard Guide for Monitoring Failure Mode Progression in Plain Bearings |
| ASTM D 5969 : 2021 | Standard Test Method for Corrosion-Preventive Properties of Lubricating Greases in Presence of Dilute Synthetic Sea Water Environments |
| ASTM D 8506 : 2023 | Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems |
| ASTM D 8029 : 2023 | Standard Specification for Biodegradable, Low Aquatic Toxicity Hydraulic Fluids |
| ASTM D 7752 : 2018 | Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids |
| ASTM D 4006 : 2022 | Standard Test Method for Water in Crude Oil by Distillation |
| ASTM D 6224 : 2023 | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
| ASTM D 5534 : 1994 : R2018 | Standard Test Method for Vapor-Phase Rust-Preventing Characteristics of Hydraulic Fluids |
| ASTM D 4378 : 2022 | Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines |
| ASTM D 7155 : 2020 | Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 91 : 1997 | Standard Test Method for Precipitation Number of Lubricating Oils |
| ASTM A 240/A240M : 2011 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM D 2422 : 1997 | Standard Classification of Industrial Fluid Lubricants by Viscosity System |
| ASTM A 240/A240M : 2005 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM A 240/A240M : 2022 : REV B | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM A 240/A240M : 2023 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM A 240/A240M : 2022 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM D 3603 : 1993 : R1997 | Standard Test Method for Rust-Preventing Characteristics of Steam Turbine Oil in the Presence of Water (Horizontal Disk Method) |
| ASTM A 240/A240M : 2022 : REV A | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM A 240/A240M : 2020 : REV A | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM E 1 : 2014 : R2020 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM A 240/A240M : 2023 : REV A | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.