ASTM D 6024/D6024M : 2016
Current
The latest, up-to-date edition.
Standard Test Method for Ball Drop on Controlled Low Strength Material (CLSM) to Determine Suitability for Load Application
Hardcopy , PDF
English
01-12-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 18
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method explains the determination of the ability of Controlled Low Strength Material (CLSM) to withstand loading by repeatedly dropping a metal weight onto the in-place material.
1.2All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.2.1The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.
1.3Units—The values stated in either SI units or inch-pound units presented in brackets are to be regarded separately as standard. The values stated in each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4CLSM is also known as flowable fill, controlled density fill, soil-cement slurry, soil-cement grout, unshrinkable fill, “K-Krete,” and other similar names.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 6023 : 1996 | Standard Test Method for Unit Weight, Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low Strength Material (CLSM) |
| ASTM D 653 : 2007 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 3740 : 2012 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 4832 : 2016 | Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders |
| ASTM D 6023 : 2015 | Standard Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low-Strength Material (CLSM) |
| ASTM D 3740 : 2023 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2019 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2004 : REV A : EDT 1 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM C 125 : 2024 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 3740 : 2008 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2013 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 6026 : 2006 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 6023 : 2002 | Standard Test Method for Unit Weight, Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low Strength Material (CLSM) |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 3740 : 1999 : REV C | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 653 : 2024 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 653 : 2022 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 4832 : 2010 | Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders |
| ASTM D 653 : 2020 : EDT 1 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 6026 : 1999 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2011 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 4832 : 2016 : EDT 1 | Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders |
| ASTM D 6026 : 2001 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2010 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 653 : 2021 : REV A | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 6026 : 1996 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2004 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6103 : 2004 | Standard Test Method for Flow Consistency of Controlled Low Strength Material (CLSM) (Withdrawn 2013) |
| ASTM D 4832 : 2002 | Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders |
| ASTM D 3740 : 2001 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 653 : 2021 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 653 : 2021 : REV B | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 6023 : 2016 | Standard Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low-Strength Material (CLSM) |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 6026 : 1996 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2012 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 4832 : 1995 : EDT 1 | Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders |
| ASTM D 6103 : 1997 | Standard Test Method for Flow Consistency of Controlled Low Strength Material (CLSM) |
| ASTM D 3740 : 2003 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2021 | Standard Practice for Using Significant Digits and Data Records in Geotechnical Data |
| ASTM D 653 : 2024 : REV A | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM D 6026 : 2001 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 6023 : 2007 | Standard Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low-Strength Material (CLSM) |
| ASTM D 3740 : 2004 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.