ASTM D 5994/D5994M : 2010 : R2015 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measuring Core Thickness of Textured Geomembranes
Hardcopy , PDF
10-07-2021
English
12-06-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.13, 2017 Describes a procedure for the measurement of core thickness of textured geomembranes.
| Committee |
D 35
|
| DevelopmentNote |
Supersedes ASTM D 5994. (06/2015)
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers a procedure to measure the core thickness of textured geomembranes.
1.2This test method does not provide thickness values for geomembranes under variable normal stresses.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 7272 : 2006 : R2018 | Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Premanufactured Taped Methods |
| ASTM D 7466/D7466M : 2010 : R2015 : EDT 1 | Standard Test Method for Measuring Asperity Height of Textured Geomembranes |
| ASTM D 7272 : 2006 | Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Pre-manufactured Taped Methods |
| ASTM D 6392 : 2012 | Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods |
| ASTM D 6434 : 2012 : R2018 | Standard Guide for the Selection of Test Methods for Flexible Polypropylene Geomembranes |
| ASTM D 5889/D5889M : 2018 | Standard Practice for Quality Control of Geosynthetic Clay Liners |
| ASTM D 6693/D6693M : 2020 | Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes |
| ASTM D 6495/D6495M : 2018 | Standard Guide for Acceptance Testing Requirements for Geosynthetic Clay Liners |
| ASTM D 5199 : 2012 : R2019 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 6495/D6495M : 2018 : REDLINE | Standard Guide for Acceptance Testing Requirements for Geosynthetic Clay Liners |
| ASTM D 4439 : 2017-08 | TERMINOLOGY FOR GEOSYNTHETICS |
| ASTM D 6693/D6693M : 2004 : R2015 : EDT 1 | Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes |
| ASTM D 6392 : 2012 : R2018 | Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods |
| ASTM D 5889/D5889M : 2018 : REDLINE | Standard Practice for Quality Control of Geosynthetic Clay Liners |
| ASTM D 7272 : 2006 : R2011 | Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Pre-manufactured Taped Methods |
| ASTM D 4439 : 2020 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2015 | Standard Terminology for Geosynthetics |
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM D 4354 : 2012 | Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing |
| ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM D 4354 : 2012 : R2020 | Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products (RECPs) for Testing |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4439 : 2011 | Standard Terminology for Geosynthetics |
| ASTM E 2554 : 2013 | Standard Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method Using Control Chart Techniques |
| ASTM D 4439 : 2015 : REV A | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2002 | Standard Terminology for Geosynthetics |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2554 : 2018 : EDT 1 | Standard Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method Using Control Chart Techniques |
| ASTM D 4439 : 2017 | Standard Terminology for Geosynthetics |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2554 : 2007 | Standard Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method in a Single Laboratory Using a Control Sample Program |
| ASTM D 4439 : 2001 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2014 | Standard Terminology for Geosynthetics |
| ASTM D 4354 : 1999 : R2009 | Standard Practice for Sampling of Geosynthetics for Testing |
| ASTM D 4354 : 2012 : REDLINE | Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing |
| ASTM E 2554 : 2018 | Standard Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method Using Control Chart Techniques |
| ASTM D 4354 : 1999 | Standard Practice for Sampling of Geosynthetics for Testing |
| ASTM D 4439 : 2004 | Standard Terminology for Geosynthetics |
| ASTM E 2554 : 2013-05 | PRACTICE FOR ESTIMATING AND MONITORING THE UNCERTAINTY OF TEST RESULTS OF A TEST METHOD USING CONTROL CHART TECHNIQUES |
| ASTM D 4439 : 2017-08 | TERMINOLOGY FOR GEOSYNTHETICS |
| ASTM D 4439 : 2000 | Standard Terminology for Geosynthetics |
| ASTM D 4354 : 1999 : R2004 | Standard Practice for Sampling of Geosynthetics for Testing |
| ASTM D 4439 : 2018 | Standard Terminology for Geosynthetics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.