ASTM D 5827 : 1995
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography
Hardcopy , PDF
11-11-2014
English
01-01-1995
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 15
|
| DocumentType |
Test Method
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This test method covers the chemical analysis of engine coolant for chloride ion by high-performance ion chromatography (HPIC). Several other common anions found in engine coolant can be determined in one chromatographic analysis by this test method.
1.2 This test method is applicable to both new and used engine coolant.
1.3 Coelution of other ions may cause interferences for any of the listed anions. In the case of unfamiliar formulations, identification verification should be performed by either or both fortification and dilution of the sample matrix with the anions of interest.
1.4 Analysis can be performed directly by this test method without pretreatment, other than dilution, as required by the linear ranges of the equipment. Table 1 indicates several applicable anions and approximate detection limits.
1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.
| ASTM D 7388 : 2018 | Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO) |
| ASTM E 1177 : 2014 | Standard Specification for Engine Coolant Grade Glycol |
| ASTM D 7517 : 2019 | Standard Specification for Fully-Formulated 1,3 Propanediol (PDO) Base Engine Coolant for Heavy-Duty Engines |
| ASTM D 7640 : 2016 | Standard Specification for Engine Coolant Grade Glycerin |
| ASTM D 8149 : 2017 | Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants |
| ASTM D 3585 : 2008 : R2013 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 7328 : 2017 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 7319 : 2017 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography |
| ASTM D 8116 : 2018 | Standard Specification for Fully-Formulated Non-Aqueous Engine Coolant for Heavy-Duty Engines (Withdrawn 2019) |
| ASTM D 4985 : 2010 : R2015 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
| ASTM D 7518 : 2010 : R2015 : EDT 1 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 7713 : 2018 | Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal) |
| ASTM D 2847 : 2015 | Standard Practice for Testing Engine Coolants in Car and Light Truck Service |
| ASTM D 3306 : 2019 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 7714 : 2011 : R2016 : EDT 1 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 8039 : 2016 | Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems |
| ASTM D 5752 : 2010 : R2017 | Standard Specification for Supplemental Coolant Additives (SCAs) for Use in Precharging Coolants for Heavy-Duty Engines |
| ASTM D 8085 : 2017 | Standard Specification for Non-Aqueous Engine Coolant for Automobile and Light-Duty Service |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.