ASTM D 5490 : 1993 : R2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Comparing Ground-Water Flow Model Simulations to Site-Specific Information
Hardcopy , PDF
11-11-2014
English
15-11-1993
CONTAINED IN VOL. 04.08, 2018 Defines techniques used in comparing results of ground-water flow model simulations to measured field data as part of a process for calibrating a ground-water model.
Committee |
D 18
|
DocumentType |
Guide
|
Pages |
8
|
ProductNote |
Reconfirmed 2002
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This guide covers techniques that should be used to compare the results of ground-water flow model simulations to measured field data as a part of the process of calibrating a ground-water model. This comparison produces quantitative and qualitative measures of the degree of correspondence between the simulation and site-specific information related to the physical hydrogeologic system.
1.2 During the process of calibration of a ground-water flow model, each simulation is compared to site-specific information such as measured water levels or flow rates. The degree of correspondence between the simulation and the physical hydrogeologic system can then be compared to that for previous simulations to ascertain the success of previous calibration efforts and to identify potentially beneficial directions for further calibration efforts.
1.3 By necessity, all knowledge of a site is derived from observations. This guide does not address the adequacy of any set of observations for characterizing a site.
1.4 This guide does not establish criteria for successful calibration, nor does it describe techniques for establishing such criteria, nor does it describe techniques for achieving successful calibration.
1.5 This guide is written for comparing the results of numerical ground-water flow models with observed site-specific information. However, these techniques could be applied to other types of ground-water related models, such as analytical models, multiphase flow models, noncontinuum (karst or fracture flow) models, or mass transport models.
1.6 This guide is one of a series of guides on ground-water modeling codes (software) and their applications. Other standards have been prepared on environmental modeling, such as Practice E 978.
1.7 The values stated in SI units are to be regarded as the standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.9 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word "Standard" in the title of this document means only that the document has been approved through the ASTM consensus process.
ASTM D 5447 : 2017 | Standard Guide for Application of a Numerical Groundwater Flow Model to a Site-Specific Problem |
ASTM D 5981/D5981M : 2018 | Standard Guide for Calibrating a Groundwater Flow Model Application |
ASTM D 6033 : 2016 | Standard Guide for Describing the Functionality of a Groundwater Modeling Code |
ASTM D 5718 : 2013 | Standard Guide for Documenting a Groundwater Flow Model Application (Withdrawn 2022) |
ASTM D 6000/D6000M : 2015 : EDT 1 | Standard Guide for Presentation of Water-Level Information from Groundwater Sites (Withdrawn 2024) |
ASTM D 5611 : 1994 : R2016 | Standard Guide for Conducting a Sensitivity Analysis for a Groundwater Flow Model Application |
ASTM D 6170 : 2017 | Standard Guide for Selecting a Groundwater Modeling Code |
ASTM E 2081 : 2000 : R2015 | Standard Guide for Risk-Based Corrective Action |
ASTM D 5719 : 2013 | Standard Guide for Simulation of Subsurface Airflow Using Groundwater Flow Modeling Codes (Withdrawn 2022) |
ASTM D 6030 : 2015 | Standard Guide for Selection of Methods for Assessing Groundwater or Aquifer Sensitivity and Vulnerability (Withdrawn 2024) |
ASTM D 653 : 2014 : REDLINE | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.