ASTM D 5452 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration
Hardcopy , PDF
26-05-2023
English
21-10-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the gravimetric determination by filtration of particulate contaminant in a sample of aviation turbine fuel delivered to a laboratory.
1.1.1The sample is filtered through a test membrane and a control membrane using vacuum. The mass change difference identifies the contaminant level per unit volume.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 4.2, 7.3, 7.5, 11.2, and X1.7.2. Before using this standard, refer to supplier's safety labels, material safety data sheets, and technical literature.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6824 : 2023 | Standard Test Method for Determining Filterability of Aviation Turbine Fuel |
| ASTM D 8111 : 2023 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
| ASTM D 873 : 2022 | Standard Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method) |
| ASTM D 7566 : 2022 : REV A | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
| ASTM D 1655 : 2022 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 6468 : 2022 | Standard Test Method for High Temperature Stability of Middle Distillate Fuels |
| ASTM D 2276 : 2006 : R2014 | Standard Test Method for Particulate Contaminant in Aviation Fuel by Line Sampling |
| ASTM D 873 : 2012 : R2018 | Standard Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method) |
| ASTM D 6615 : 2015 : REV A : R2019 | Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel |
| ASTM D 6986 : 2003 : R2020 | Standard Test Method for Free Water, Particulate and Other Contamination in Aviation Fuels (Visual Inspection Procedures) |
| ASTM D 6984 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine |
| ASTM D 4865 : 2019 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 6824 : 2013 : R2018 | Standard Test Method for Determining Filterability of Aviation Turbine Fuel |
| ASTM D 6217 : 2021 | Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration<rangeref></rangeref > |
| ASTM D 7843 : 2021 | Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry |
| ASTM D 4306 : 2020 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
| ASTM D 6469 : 2020 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 7320 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
| ASTM D 8111 : 2021 : REV A : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
| ASTM D 4865 : 2019 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 6615 : 2001 | Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel |
| ASTM D 2276 : 2006 : R2014 | Standard Test Method for Particulate Contaminant in Aviation Fuel by Line Sampling |
| ASTM D 3828 : 1998 | Standard Test Methods for Flash Point by Small Scale Closed Tester |
| ASTM D 3828 : 2016 : REV A : R2021 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 6615 : 2022 | Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel |
| ASTM D 93 : 2019 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 6615 : 2015 : REV A : R2019 | Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel |
| ASTM D 93 : 1990 : EDT 1 | Standard Test Methods for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 56 : 2021 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 8194 : 2018 : EDT 1 | Standard Practice for Evaluation of Suitability of 37 mm Filter Monitors and 47 mm Filters Used to Determine Particulate Contaminant in Aviation Turbine Fuels |
| ASTM D 3828 : 2016 : REV A | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 56 : 2016 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 4865 : 1998 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 56 : 2021 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 2244 : 2022 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 93 : 2000 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 93 : 1985 | Standard Test Method for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 56 : 2022 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 4306 : 2020 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
| ASTM D 56 : 1987 | Standard Test Method for Flash Point by Tag Closed Tester |
| ASTM D 2276 : 2022 | Standard Test Method for Particulate Contaminant in Aviation Fuel by Line Sampling |
| ASTM D 93 : 1997 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 93 : 2018 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.