ASTM D 5404/D5404M : 2021
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator
Hardcopy , PDF
23-10-2024
English
01-11-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 04
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice is intended to recover asphalt from a solvent using the rotary evaporator to ensure that changes in the asphalt properties during the recovery process are minimized.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.2.1Residual pressure measurements are shown in both the SI unit of kPa and the commonly used non-standard equivalent unit of “mm of Hg.”
1.2.2Measurements of volume and mass are only given in SI units because they are the only units typically used in practice when performing this standard practice.
1.3The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 2172/D2172M : 2017 : EDT 1 | Standard Test Methods for Quantitative Extraction of Asphalt Binder from Asphalt Mixtures |
| ASTM D 2172/D2172M : 2024 | Standard Test Methods for Quantitative Extraction of Asphalt Binder from Asphalt Mixtures |
| ASTM D 6368 : 2006 : R2018 | Standard Specification for Vapor-Degreasing Solvents Based on <emph type="bdit">normal</emph >-Propyl Bromide and Technical Grade <emph type="bdit">normal</emph >-Propyl Bromide |
| ASTM E 2251 : 2014 : R2021 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM E 2251 : 2014 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM D 3666 : 2016 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6368 : 2006 : R2023 | Standard Specification for Vapor-Degreasing Solvents Based on <emph type="bdit">normal</emph >-Propyl Bromide and Technical Grade <emph type="bdit">normal</emph >-Propyl Bromide |
| ASTM E 1 : 2014 : R2020 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 3666 : 2024 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.