ASTM D 5110 : 1998 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry
Hardcopy , PDF
10-10-2022
English
06-10-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 11.03, 2017 Defines a means for calibrating ambient, workplace, or indoor ozone monitors, and for certifying transfer standards to be used for that purpose.
| Committee |
D 22
|
| DocumentType |
Standard Practice
|
| Pages |
8
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers a means for calibrating ambient, workplace, or indoor ozone monitors, and for certifying transfer standards to be used for that purpose.
1.2This practice describes means by which dynamic streams of ozone in air can be designated as primary ozone standards.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 8 for specific precautionary statements.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5011 : 2017 | Standard Practices for Calibration of Ozone Monitors Using Transfer Standards |
| ASTM D 5156 : 2002 : R2016 | Standard Test Methods for Continuous Measurement of Ozone in Ambient, Workplace, and Indoor Atmospheres (Ultraviolet Absorption) |
| ASTM D 5149 : 2002 : R2016 | Standard Test Method for Ozone in the Atmosphere: Continuous Measurement by Ethylene Chemiluminescence |
| ASTM D 5156 : 2022 | Standard Test Methods for Continuous Measurement of Ozone in Ambient, Workplace, and Indoor Atmospheres (Ultraviolet Absorption) |
| ASTM D 3195 : 1990 : R2004 | Standard Practice for Rotameter Calibration |
| ASTM E 220 : 2019 | Standard Test Method for Calibration of Thermocouples By Comparison Techniques |
| ASTM E 591 : 1980 | Practice for Safety and Health Requirements Relating to Occupational Exposure to Ozone (Withdrawn 1990) |
| ASTM D 1356 : 2015 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 3249 : 1995 : R2011 | Standard Practice for General Ambient Air Analyzer Procedures |
| ASTM D 3249 : 1995 : R2000 | Standard Practice for General Ambient Air Analyzer Procedures |
| ASTM D 1356 : 2017 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5011 : 1992 : R1997 : EDT 1 | Standard Practices for Calibration of Ozone Monitors Using Transfer Standards |
| ASTM D 3631 : 1999 : R2004 | Standard Test Methods for Measuring Surface Atmospheric Pressure |
| ASTM D 5011 : 1992 : R2003 | Standard Practices for Calibration of Ozone Monitors Using Transfer Standards |
| ASTM D 1356 : 2015 : REV B | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 3249 : 1995 : R2005 | Standard Practice for General Ambient Air Analyzer Procedures |
| ASTM D 1356 : 2014 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 3631 : 1999 : R2007 | Standard Test Methods for Measuring Surface Atmospheric Pressure |
| ASTM D 3249 : 1995 : R2019 | Standard Practice for General Ambient Air Analyzer Procedures |
| ASTM D 3631 : 1999 : R2011 | Standard Test Methods for Measuring Surface Atmospheric Pressure |
| ASTM D 1356 : 2015 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2005 : R2010 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM E 220 : 2013 : REDLINE | Standard Test Method for Calibration of Thermocouples By Comparison Techniques |
| ASTM D 1356 : 2020 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5011 : 2017 | Standard Practices for Calibration of Ozone Monitors Using Transfer Standards |
| ASTM D 1356 : 2000 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5011 : 2017 : REDLINE | Standard Practices for Calibration of Ozone Monitors Using Transfer Standards |
| ASTM D 1356 : 2014 : REV B | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2014 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 5011 : 1992 : R2009 | Standard Practices for Calibration of Ozone Monitors Using Transfer Standards |
| ASTM D 1356 : 2005 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 3631 : 1999 | Standard Test Methods for Measuring Surface Atmospheric Pressure |
| ASTM D 3631 : 1999 : R2017 | Standard Test Methods for Measuring Surface Atmospheric Pressure |
| ASTM D 3195 : 1990 : R1998 : EDT 1 | Standard Practice for Rotameter Calibration |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.