ASTM D 5018 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Shear Viscosity of Coal-Tar and Petroleum Pitches
Hardcopy , PDF
09-11-2023
English
19-07-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the apparent shear viscosity of coal-tar and petroleum-based pitches having a Mettler softening point (SP) range of approximately 95 °C to 120 °C (see Test Method D3104).
1.2This test method is applicable only for rotational viscometers.
1.3Since this test method is based on theoretical grounds, strict adherence to details of the procedure is necessary to comply with the theoretical requirements.
1.4The values stated in SI units are to be regarded as standard.
1.4.1Exception—The values stated in conventional units (centipoise) are to be regarded as the standard for viscosity measurement only. The SI unit is the pascal second (Pa·s) and one millipascal second (mPa·s) = one centipoise (cP); centipoise is in cgs units.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 2975 : 2015 | Standard Test Method for Calibration of Concentric Cylinder Rotational Viscometers |
| ASTM E 2975 : 2014 | Standard Test Method for Calibration of Concentric Cylinder Rotational Viscometers |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4296 : 1983 : R1999 | Standard Practice for Sampling Pitch |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2975 : 2023 | Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4296 : 1983 : R2015 : EDT 1 | Standard Practice for Sampling Pitch |
| ASTM E 1953 : 1998 | Standard Practice for Description of Thermal Analysis Apparatus |
| ASTM E 2975 : 2016 | Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers |
| ASTM D 3104 : 1999 | Standard Test Method for Softening Point of Pitches (Mettler Softening Point Method) |
| ASTM E 2975 : 2016 : EDT 1 | Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.