ASTM D 4678 : 2015 : REV A : R2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Rubber—Preparation, Testing, Acceptance, Documentation, and Use of Reference Materials
Hardcopy , PDF
09-01-2024
English
18-12-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 11
|
| DocumentType |
Standard Practice
|
| Pages |
24
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers materials used on an industry-wide basis as reference materials, which are vitally important to conduct product, specification, and development testing in the rubber industry. This practice describes the steps necessary to ensure that any candidate material, that has a perceived need, can become a Reference Material. The practice sets forth the recommendations on the preparation steps for these materials, on the testing that shall be conducted to permit acceptance of any candidate material, and on how the documentation needed for the acceptance shall be recorded for future use and review.
1.2This practice shall be administered by ASTM Committee D11.
1.2.1Important sections of this practice are as follows:
| Section | |
| Significance and Use | 3 |
| Preparation of Industry Reference Materials | 4 |
| Overview of Industry Reference Material Testing | 5 |
| Chemical and Physical Specifications for IRM | 6 |
| Reference Material Documentation | 7 |
| Typical Reference Material Use | 8 |
| Recommended Package Size for IRM | Annex A1 |
| Recommended Sampling Plans for Homogeneity Testing of an IRM | Annex A2 |
| Test Plan and Analysis for Homogeneity of an IRM | Annex A3 |
| Test Plan and Analysis to Evaluate an Accepted Reference Value | Annex A4 |
| Statistical Model(s) for IRM Testing | Annex A5 |
| Example of Annex Calculations for a Typical IRM | Appendix X1 |
| Two-Way Analysis of Variance for Calculating Sr | Appendix X2 |
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5900 : 2017 : EDT 1 | Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM) |
| ASTM D 7850 : 2019 | Standard Specification for Biological Properties of Industry Reference Materials (IRM) |
| ASTM D 3182 : 2016 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 5964 : 2016 | Standard Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil |
| ASTM D 7427 : 2016 | Standard Test Method for Immunological Measurement of Four Principal Allergenic Proteins (Hev b 1, 3, 5 and 6.02) in Hevea Natural Rubber and Its Products Derived from Latex |
| ASTM D 5964 : 2016 : R2021 | Standard Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil |
| ASTM E 826 : 2014 | Standard Practice for Testing Homogeneity of a Metal Lot or Batch in Solid Form by Spark Atomic Emission Spectrometry (Withdrawn 2023) |
| ASTM D 4483 : 2020 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
| ASTM D 5900 : 2023 | Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM) |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 122 : 2017 : R2022 | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
| ASTM E 122 : 2017 | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 5900 : 2020 | Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM) |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 5900 : 1998 | Standard Specification for Physical and Chemical Properties of Industry Reference Materials (IRM) |
| ASTM D 4483 : 2018 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.