ASTM D 4317 : 2016 : REDLINE
Current
The latest, up-to-date edition.
Standard Specification for Polyvinyl Acetate-Based Emulsion Adhesives
English
23-05-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 15.06, 2016 Specifies polyvinyl acetate or polyvinyl acetate copolymer resin emulsion adhesives used on wood, wood-based substrates, or plastic laminates.
| Committee |
D 14
|
| DevelopmentNote |
Supersedes A A 3001. (06/2003)
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers polyvinyl acetate or polyvinyl acetate copolymer resin emulsion adhesives suitable for use on wood, wood-based substrates, or plastic laminates. It does not cover the group of polyvinyl-based adhesives which are suitable for bonding flexible films.
1.2The adhesives are classified at three performance levels in accordance with water-resistance as shown in Table 1 and Table 2. See Section 5 for a description of the expected exposure conditions for each class of adhesive. See Table X1.1 for a classification of typical end products that are manufactured using adhesives at the three performance levels covered by this specification.
1.3The following index is provided as a guide to the test methods portion of this specification:
| Section | |
| Tests for Physical Properties | 9 |
| Viscosity | 9.1.1 |
| Density | 9.1.2 |
| Nonvolatiles | 9.1.3 |
| pH | 9.1.4 |
| Tests for Adhesive Bond | 10 |
| Block Shear Strength, Compression | 10.2 |
| Plywood Shear Tests | 10.3 |
1.4The values stated in SI units are to be regarded as the standard. The values given in parenthesis are for information purposes only.
1.5The following safety hazards caveat pertains only to the test method portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ISO 26842-1:2013 | Adhesives Test methods for the evaluation and selection of adhesives for indoor wood products Part 1: Resistance to delamination in non-severe environments |
| AA-B-2825 Base Document:1994 | BED, BUNK, STEEL, SQUARE TUBE, WITH END PANELS SINGLE AND DOUBLE-DECK |
| 10/30229682 DC : 0 | BS ISO 26842-2 - ADHESIVES - TEST METHODS FOR THE EVALUATION AND SELECTION OF ADHESIVES FOR INDOOR WOOD PRODUCTS - PART 2: RESISTANCE TO DELAMINATION IN SEVERE ENVIRONMENTS |
| ASTM D 6465 : 1999 : R2012 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| AA-P-2930 Base Document:1997 | PANEL FOR BUNK BED |
| ASTM D 6465 : 1999 : R2016 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| ASTM D 6465 : 1999 : R2005 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| CEN/TS 17035:2017 | Surface Active Agents - Bio-based surfactants - Requirements and test methods |
| 10/30229679 DC : 0 | BS ISO 26842-1 - ADHESIVES - TEST METHODS FOR THE EVALUATION AND SELECTION OF ADHESIVES FOR INDOOR WOOD PRODUCTS - PART 1: RESISTANCE TO DELAMINATION IN NON-SEVERE ENVIRONMENTS |
| BS ISO 26842-1:2013 | Adhesives. Test methods for the evaluation and selection of adhesives for indoor wood products Resistance to delamination in non-severe environments |
| 07/30151497 DC : 0 | ISO 26842 - ADHESIVES - GUIDELINES FOR THE SELECTION OF ADHESIVES FOR INDOOR WOOD PRODUCTS BY DURABILITY TESTING |
| BS ISO 26842-2:2013 | Adhesives. Test methods for the evaluation and selection of adhesives for indoor wood products Resistance to delamination in severe environments |
| S.R. CEN/TS 17035:2017 | SURFACE ACTIVE AGENTS - BIO-BASED SURFACTANTS - REQUIREMENTS AND TEST METHODS |
| MIL-DTL-2439 Revision G:2014 | CONTAINER, AMMUNITION, FIBER, SPIRALLY WOUND |
| ISO 26842-2:2013 | Adhesives Test methods for the evaluation and selection of adhesives for indoor wood products Part 2: Resistance to delamination in severe environments |
| MIL-B-28644 Revision A:1988 | BED, BUNK, STEEL, SQUARE TUBE, WITH END PANELS, SINGLE AND DOUBLE-DECK |
| AA-B-2892 Base Document:1997 | BED, BUNK, STEEL, SINGLE AND DOUBLE-DECK (CONVERTIBLE TYPE) |
| ASTM D 907 : 2015 : REDLINE | Standard Terminology of Adhesives |
| AA-B-606 Revision D:1993 | BOX, FILING, WOOD |
| PD CEN/TS 17035:2017 | Surface Active Agents. Bio-based surfactants. Requirements and test methods |
| A-A-3001 Base Document:1996 | ADHESIVE, POLYVINYL ACETATE EMULSION, WOOD AND PLASTIC |
| ASTM D 6465 : 1999 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| PPP-C-96 Revision E:1992 | CAN, METAL, 28 GAGE AND LIGHTER |
| ASTM D 1490 : 2001 : R2018 | Standard Test Method for Nonvolatile Content of Urea-Formaldehyde Resin Solutions |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| ASTM D 1875 : 2003 | Standard Test Method for Density of Adhesives in Fluid Form |
| ASTM D 1084 : 2016 : REDLINE | Standard Test Methods for Viscosity of Adhesives |
| ASTM E 70 | TEST METHOD FOR PH OF AQUEOUS SOLUTIONS WITH THE GLASS ELECTRODE |
| FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
| ASTM D 907 : 2015 : REDLINE | Standard Terminology of Adhesives |
| PPP-D-729 Revision E:1977 | DRUMS, SHIPPING AND STORAGE, STEEL, 55 GALLON (208 LITERS) |
| ASTM D 905 : 2008 | Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading |
| ASTM E 1953 : 2014 : REDLINE | Standard Practice for Description of Thermal Analysis and Rheology Apparatus |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.