ASTM D 3828 : 1998
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Flash Point by Small Scale Closed Tester
Hardcopy , PDF
11-11-2014
English
31-12-2010
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 These test methods cover procedures for the determination of the flash point by a small scale closed tester. The procedures may be used to determine the actual flash point temperature of a sample or whether a product will or will not flash at a specified temperature (flash/no flash).
1.2 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.
1.3 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Note 8, Table 1, Footnote B, A2.1, A2.2 and the Material Safety Data Sheets for the product being tested.
| ASTM D 3699 : 2018 : REV A | Standard Specification for Kerosine |
| ASTM D 1655 : 2019 | Standard Specification for Aviation Turbine Fuels |
| ASTM E 1232 : 2007 : R2019 | Standard Test Method for Temperature Limit of Flammability of Chemicals |
| ASTM E 502 : 2007 : R2013 | Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods |
| ASTM D 7467 : 2019 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 6823 : 2008 : R2013 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
| ASTM D 396 : 2019 | Standard Specification for Fuel Oils |
| ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
| ASTM D 7566 : 2019 | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
| ASTM D 5452 : 2012 | Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration |
| ASTM D 6751 : 2019 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 4171 : 2016 : REV A | Standard Specification for Fuel System Icing Inhibitors |
| ASTM D 4054 : 2019 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
| ASTM F 3363 : 2019 | Standard Specification for Unvented Liquid/Gel Fuel-Burning Portable Devices |
| ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM D 7236 : 2016 : REV A | Standard Test Method for Flash Point by Small Scale Closed Cup Tester (Ramp Method) |
| ASTM D 6468 : 2008 : R2019 | Standard Test Method for High Temperature Stability of Middle Distillate Fuels |
| ASTM D 7215 : 2016 | Standard Test Method for Calculated Flash Point from Simulated Distillation Analysis of Distillate Fuels |
| ASTM D 56 : 2016 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 3757 : 2016 | Standard Guide for Preparing Specifications for Solvent-based Floor Polishes |
| ASTM D 8174 : 2018 | Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Small-Scale Closed Cup Tester |
| ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 7223 : 2017 | Standard Specification for Aviation Certification Turbine Fuel |
| ASTM D 6074 : 2015 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
| ASTM D 5452 : 2020 | Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration |
| ASTM D 975 : 2020 : REV C | Standard Specification for Diesel Fuel |
| ASTM D 3699 : 2019 | Standard Specification for Kerosine |
| ASTM D 396 : 2020 | Standard Specification for Fuel Oils |
| ASTM D 6751 : 2020 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 7666 : 2012 : R2019 | Standard Specification for Triglyceride Burner Fuel |
| ASTM D 6217 : 2018 | Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration |
| ASTM D 3934 : 2020 | Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus |
| ASTM D 7467 : 2020 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 7566 : 2020 : REV C | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
| ASTM D 1655 : 2020 : REV D | Standard Specification for Aviation Turbine Fuels |
| ASTM D 2880 : 2020 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4054 : 2020 : REV C | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
| ASTM D 8147 : 2017 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
| ASTM D 3934 : 2014 | Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.