ASTM D 3675 : 2021 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source
Hardcopy , PDF
28-04-2022
English
27-04-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This is a fire test response standard.
1.2This test method describes the measurement of surface flammability of flexible cellular materials.
1.3This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not, by itself, incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
1.6Specific information about hazards is given in Section 7.
Note 1:There is no known ISO equivalent to this standard.
1.7The values stated in SI units are to be regarded as the standard. The values stated in inch-pound units, in parentheses, are for information only and are approximations (see also IEEE/ASTM SI-10).
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 1534 : 2016 | Standard Test Method for Determining Changes in Fire-Test-Response Characteristics of Cushioning Materials After Water Leaching |
| ASTM E 162 : 2016 | Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source |
| ASTM D 3453 : 2020 | Standard Specification for Flexible Cellular Materials—Urethane for Furniture and Automotive Cushioning, Bedding, and Similar Applications |
| ASTM E 2061 : 2020 | Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles |
| ASTM F 1870 : 2016 | Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities |
| ASTM E 3020 : 2016 : REV A | Standard Practice for Ignition Sources |
| ASTM D 3574 : 2017 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM C 1482 : 2017 | Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation |
| ASTM E 176 : 2021 : REV A | Standard Terminology of Fire Standards |
| ASTM E 162 : 2021 | Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source |
| ASTM E 1546 : 2015 | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM E 162 : 2021 | Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source |
| ASTM E 176 : 2018 : REV A : EDT 1 | Standard Terminology of Fire Standards |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 176 : 2021 | Standard Terminology of Fire Standards |
| ASTM E 176 : 2018 : REV A : EDT 2 | Standard Terminology of Fire Standards |
| ASTM E 1546 : 2021 | Standard Guide for Development of Fire-Hazard-Assessment Standards |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 456 : 2013 : REV A : R2017 : EDT 6 | Standard Terminology Relating to Quality and Statistics |
| ASTM E 176 : 2021 : REV A | Standard Terminology of Fire Standards |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.