ASTM D 3464 : 1996 : R2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Average Velocity in a Duct Using a Thermal Anemometer
Hardcopy , PDF
18-10-2024
English
05-06-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 11.03, 2015 Describes the measurement of the average velocity with a thermal anemometer for the purpose of determining gas flow in a stack, duct, or flue.
| Committee |
D 22
|
| DocumentType |
Test Method
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2014
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method describes the measurement of the average velocity with a thermal anemometer for the purpose of determining gas flow in a stack, duct, or flue (1-5).2 It is limited to those applications where the gas is essentially air at ambient conditions and the temperature, moisture, and contaminant loading are insignificant as sources of error compared to the basic accuracy of the typical field situation.
1.2The range of the test method is from 1 to 30 m/s (3 to 100 ft/s).
1.3The values stated in SI units are to be regarded as the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM B 827 : 2005 : R2020 | Standard Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests |
| ASTM D 6060 : 2017 | Standard Test Method for Sampling of Process Vents with a Portable Gas Chromatograph |
| ASTM B 827 : 2005 : R2014 | Standard Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests |
| ASTM D 3796 : 1990 : R1998 | Standard Practice for Calibration of Type S Pitot Tubes |
| ASTM D 1356 : 2015 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2017 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 3796 : 1990 : R2004 | Standard Practice for Calibration of Type S Pitot Tubes |
| ASTM D 1356 : 2015 : REV B | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2014 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 3796 : 2009 : R2016 | Standard Practice for Calibration of Type S Pitot Tubes |
| ASTM D 1356 : 2015 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2005 : R2010 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2020 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2000 : REV A | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2014 : REV B | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2014 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 1356 : 2005 | Standard Terminology Relating to Sampling and Analysis of Atmospheres |
| ASTM D 3796 : 2009 | Standard Practice for Calibration of Type S Pitot Tubes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.