ASTM D 3308 : 2012 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for PTFE Resin Skived Tape
Hardcopy , PDF
17-06-2022
English
13-09-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 08.02, 2017 Specifies skived tape in thicknesses from 0.013 to 6.35 mm (0.0005 to 0.250 in.) manufactured by skiving from PTFE resin molding and extrusion materials.
| Committee |
D 20
|
| DevelopmentNote |
Supersedes MIL P 22241 (07/2004)
|
| DocumentType |
Standard
|
| Pages |
3
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers skived tape in thicknesses from 0.013 to 6.35 mm (0.0005 to 0.250 in.) manufactured by skiving (Note 1) from PTFE resin molding and extrusion materials.
Note 1:Skiving is the process of continuously shaving a film on a lathe from the outer surface to the core of a molded cylindrical tube of material.
Note 2:Abbreviations have been approved from Terminology D1600.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only.
1.3The following hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 3:This specification and ISO 13000-1 and ISO 13000-2 differ in approach or detail, and data obtained using either may not be technically equivalent.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 336 : 2002 : R2016 | Standard Practice for Design and Construction of Nonmetallic Enveloped Gaskets for Corrosive Service |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1389 : 2006 | Standard Test Method for Proof-Voltage Testing of Thin Solid Electrical Insulating Materials |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4894 : 1998 : REV A | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 1389 : 1997 : REV A | Standard Test Method for Proof-Voltage Testing of Thin Solid Electrical Insulating Materials |
| ASTM D 4894 : 2007 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 1389 : 2007 | Standard Test Method for Proof-Voltage Testing of Thin Solid Electrical Insulating Materials (Withdrawn 2014) |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1389 : 1997 : REV A : R2004 | Standard Test Method for Proof-Voltage Testing of Thin Solid Electrical Insulating Materials |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4894 : 2004 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ISO 13000-1:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirements and designation |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 4894 : 2015 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 4894 : 2019 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 4894 : 2007 : R2012 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
| ISO 13000-2:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 2: Preparation of test specimens and determination of properties |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 374 : 1999 | Standard Test Methods for Thickness of Solid Electrical Insulation |
| ASTM D 3892 : 2015 : REDLINE | PRACTICE FOR PACKAGING/PACKING OF PLASTICS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.