ASTM D 3167 : 2010 : R2017
Current
The latest, up-to-date edition.
Standard Test Method for Floating Roller Peel Resistance of Adhesives
Hardcopy , PDF
English
01-11-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 15.06, 2017 Defines the determination of the relative peel resistance of adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing.
| Committee |
D 14
|
| DocumentType |
Test Method
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers the determination of the relative peel resistance of adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing.
1.2A variation in thickness of the adherends will generally influence the test values. For this reason, the thickness of the sheets used to make the test specimens shall be specified in the material specification. When no thickness is specified, the flexible adherend shall be 0.63 mm (0.025 in.) thick and the rigid adherend shall be 1.63 mm (0.064 in.) thick.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 790 : 2018 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM F 2207 : 2006 : R2019 | Standard Specification for Cured-in-Place Pipe Lining System for Rehabilitation of Metallic Gas Pipe |
| ASTM E 866 : 2019 | Standard Specification for Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels |
| ASTM E 865 : 2012 | Standard Specification for Structural Film Adhesives for Honeycomb Sandwich Panels |
| ASTM E 864 : 2012 | Standard Practice for Surface Preparation of Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels |
| ASTM E 1826 : 2012 | Standard Specification for Low Volatile Organic Compound (VOC) Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded |
| ASTM F 942 : 2018 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| ASTM D 6361/D6361M : 1998 : R2015 | Standard Guide for Selecting Cleaning Agents and Processes |
| ASTM D 6465 : 1999 : R2016 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| ASTM E 1749 : 2018 | Standard Terminology Relating to Rigid Wall Relocatable Shelters |
| SAE AIR6291A:2024 | Guidelines for Repair Process Evaluation of Aluminum Bonded Structure |
| ASTM D 1781 : 1998 : R2012 | Standard Test Method for Climbing Drum Peel for Adhesives |
| ASTM B 209 : 2014 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM D 907 : 2015 | Standard Terminology of Adhesives |
| ASTM D 1781 : 1998 | Standard Test Method for Climbing Drum Peel for Adhesives |
| ASTM D 907 : 2015 : R2023 | Standard Terminology of Adhesives |
| ASTM D 1781 : 1998 : R2021 | Standard Test Method for Climbing Drum Peel for Adhesives |
| ASTM D 907 : 2015 : REDLINE | Standard Terminology of Adhesives |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM D 1781 : 1998 : R2004 | Standard Test Method for Climbing Drum Peel for Adhesives |
| ASTM E 4 : 2024 | Standard Practices for Force Calibration and Verification of Testing Machines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.