ASTM D 2595 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range
Hardcopy , PDF
23-12-2022
English
07-07-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.01, 2017 Defines the determination of evaporation loss of lubricating greases at temperatures between 93 degrees C and 316 degrees C (200 degrees F and 600 degrees F).
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of evaporation loss of lubricating greases at temperatures between 93 °C and 316 °C (200 °F and 600 °F). This test method is intended to augment Test Method D972, which is limited to 149 °C (300 °F).
1.2The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety information, see 5.2.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| MIL-PRF-32014 Revision A:2006 | GREASE, AIRCRAFT AND INSTRUMENT |
| ASTM D 972 : 2016 : REDLINE | Standard Test Method for Evaporation Loss of Lubricating Greases and Oils |
| ASTM D 6185 : 2011 | Standard Practice for Evaluating Compatibility of Binary Mixtures of Lubricating Greases |
| ASTM E 1868 : 2010 | Standard Test Method for Loss-On-Drying by Thermogravimetry |
| MIL G 23827 : B | GREASE, AIRCRAFT AND INSTRUMENT, GEAR AND ACTUATOR SCREW |
| MIL-G-25537 Revision C:1984 | GREASE, AIRCRAFT, HELICOPTER OSCILLATING BEARING, NATO CODE NUMBER G-366, METRIC |
| MIL-G-21164 Revision D:1981 | GREASE, MOLYBDENUM DISULFIDE, FOR LOW AND HIGH TEMPERATURES, NAT O CODE NUMBER G353 |
| MIL-DTL-23549 Revision D:2002 | GREASE, GENERAL PURPOSE |
| MIL-G-81827 Revision A:1983 | GREASE, AIRCRAFT, HIGH LOAD CAPACITY, WIDE TEMPERATURE RANGE |
| MIL-PRF-83261 Revision C:2011 | GREASE, AIRCRAFT, EXTREME PRESSURE, ANTI-WEAR |
| MIL G 81322 : E | GREASE, AIRCRAFT, GENERAL PURPOSE, SIDE TEMPERATURE RANGE, NATO CODE NUMBER G-395 |
| ASTM D 2878 : 2010 | Standard Test Method for Estimating Apparent Vapor Pressures and Molecular Weights of Lubricating Oils |
| ASTM E 1868 : 2010 : R2015 | Standard Test Methods for Loss-On-Drying by Thermogravimetry |
| ASTM D 972 : 2016 | Standard Test Method for Evaporation Loss of Lubricating Greases and Oils |
| ASTM E 1868 : 2010 : R2021 | Standard Test Methods for Loss-On-Drying by Thermogravimetry |
| ASTM D 2878 : 2021 | Standard Test Method for Estimating Apparent Vapor Pressures and Molecular Weights of Lubricating Oils |
| SAE AMS3058 | Grease: Wide Temperature Range Lithium or Lithium Complex Thickened for Aircraft Wheel Bearings |
| MIL-PRF-27617 Revision G:2011 | GREASE, AIRCRAFT AND INSTRUMENT, FUEL AND OXIDIZER RESISTANT |
| DEFSTAN 91-55/2(1995) : 1995 | GREASE, SYNTHETIC, HIGH TEMPERATURE NATO CODE: G-372 - JOINT SERVICE DESIGNATION: XG-300 |
| MIL G 83261 : A | GREASE, AIRCRAFT, EXTREME PRESSURE, ANTI WEAR |
| DEFSTAN 91-52/1(1980) : 1980 | GREASE, AIRCRAFT: MULTI-PURPOSE NATO CODE NO. G-395 JOINT SERVICE DESIGNATION: XG-293 |
| SAE AMS3052 | Grease, Aircraft, General Purpose, Low Temperature Range, Lithium Thickened |
| MIL-G-25013 Revision E:1983 | GREASE, AIRCRAFT, BALL AND ROLLER BEARING, NATO CODE NUMBER G-372, METRIC |
| SAE J2695_200508 | Heavy Duty Vehicle Lubricating Greases |
| ASTM D 6185 : 2011 : R2017 | Standard Practice for Evaluating Compatibility of Binary Mixtures of Lubricating Greases |
| MIL-PRF-81322 Revision G:2005 | GREASE, AIRCRAFT, GENERAL PURPOSE, WIDE TEMPERATURE RANGE, NATO CODE G-395 |
| SAE MAM3053A | Grease, Water Resistant Polyalphaolefin Base |
| MIL-G-4343 Revision C:1978 | GREASE, PNEUMATIC SYSTEMS |
| DOD-G-85733 Base Document:1986 | GREASE, HIGH TEMPERATURE, CATAPULT SYSTEM |
| SAE AMSG4343A | Grease, Pneumatic System |
| SAE MS1000_201302 | Lubricants, Industrial Oils, and Related Products - Classification |
| SAE MS1011_201808 | Lubricants, Industrial Oils, and Related Products - Type X (Greases) - Specification |
| ASTM D 2878 : 2010 : R2016 | Standard Test Method for Estimating Apparent Vapor Pressures and Molecular Weights of Lubricating Oils |
| ASTM E 2877 : 2012 : EDT 1 | Standard Guide for Digital Contact Thermometers |
| ASTM D 217 : 2021 | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM A 240/A240M : 2011 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM D 217 : 2021 : REV A | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM A 240/A240M : 2005 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM D 217 : 2019 : REV B | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM A 240/A240M : 2022 : REV B | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM E 2877 : 2012 : R2019 | Standard Guide for Digital Contact Thermometers |
| ASTM A 240/A240M : 2022 | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM D 972 : 2016 : REDLINE | Standard Test Method for Evaporation Loss of Lubricating Greases and Oils |
| ASTM D 217 : 1997 | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 217 : 2017 : REDLINE | TEST METHODS FOR CONE PENETRATION OF LUBRICATING GREASE |
| ASTM E 2877 : 2012 | Standard Guide for Standard Guide for Digital Contact Thermometers |
| ASTM A 240/A240M : 2022 : REV A | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
| ASTM A 240/A240M : 2020 : REV A | Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.