ASTM D 2593 : 1993 : R2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Butadiene Purity and Hydrocarbon Impurities by Gas Chromatography
Hardcopy , PDF
09-06-2023
English
24-07-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.01, 2015 Specifies the determination of butadiene-1,3 purity and impurities such as propane, propylene, isobutane, n-butane, butene-1, isobutylene, propadiene, trans-butene-2, cis-butene-2, butadiene-1,2, pentadiene-1,4, and, methyl, dimethyl, ethyl, and vinyl acetylene in polymerization grade butadiene by gas chromatography.
| Committee |
D 02
|
| DevelopmentNote |
Also numbered as IP 194. (11/2004)
|
| DocumentType |
Test Method
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2014
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of butadiene-1,3 purity and impurities such as propane, propylene, isobutane, n-butane, butene-1, isobutylene, propadiene, trans-butene-2, cis -butene-2, butadiene-1,2, pentadiene-1,4, and, methyl, dimethyl, ethyl, and vinyl acetylene in polymerization grade butadiene by gas chromatography. Impurities including butadiene dimer, carbonyls, inhibitor, and residue are measured by appropriate ASTM procedures and the results used to normalize the component distribution obtained by chromatography.
Note 1:Other impurities present in commercial butadiene must be calibrated and analyzed. Other impurities were not tested in the cooperative work on this test method.
Note 2:This test method can be used to check for pentadiene-1,4 and other C5s instead of Test Method D1088.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.1 and 9.3.
| ASTM D 6691 : 2017 | Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in the Marine Environment by a Defined Microbial Consortium or Natural Sea Water Inoculum |
| ASTM D 2804 : 2002 : R2012 | Standard Test Method for Purity of Methyl Ethyl Ketone By Gas Chromatography (Withdrawn 2021) |
| ASTM D 3545 : 2006 : R2012 | Standard Test Method for Alcohol Content and Purity of Acetate Esters by Gas Chromatography (Withdrawn 2021) |
| ASTM D 2426 : 1993 : R2014 | Standard Test Method for Butadiene Dimer and Styrene in Butadiene Concentrates by Gas Chromatography |
| ASTM D 5274 : 2000 : R2014 | Standard Guide for Analysis of 1,3–Butadiene Product |
| ASTM D 3329 : 2003 : R2017 | Standard Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography |
| ASTM D 1088 : 1953 : R1978 | Method of Test for Boiling Point Range of Polymerization-Grade Butadiene (Withdrawn 1983) |
| IP 194 : 74(R1981) | DETERMINATION OF BUTADIENE PURITY - GAS CHROMATOGRAPHY METHOD |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.