ASTM D 2555 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Establishing Clear Wood Strength Values
Hardcopy , PDF
01-09-2016
English
01-08-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 07
|
| DocumentType |
Standard Practice
|
| Pages |
18
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers the determination of strength values for clear wood of different species in the unseasoned condition, unadjusted for end use, applicable to the establishment of design values for different solid wood products such as lumber, laminated wood, plywood, and round timbers. Presented are:
1.1.1Procedures by which test values obtained on small clear specimens may be combined with density data from extensive forest surveys to make them more representative,
1.1.2Guidelines for the interpretation of the data in terms of assigned values for combinations of species or regional divisions within a species to meet special marketing needs, and
1.1.3Information basic to the translation of the clear wood values into design values for different solid wood products for different end uses.
1.1.4For species where density survey data are not as yet available for the re-evaluation of average strength properties, the presently available data from tests made under the sampling methods and procedures of Test Methods D143 or Practice E105 are provided with appropriate provision for their application and use. Because of the comprehensive manner in which the density survey is undertaken, it follows that the re-evaluated strength data are intended to be representative of the forest stand, or rather large forest subdivisions.
1.1.5Some useful mechanical properties (tensile strengths parallel and perpendicular to grain, modulus of rigidity for a longitudinal-transverse plane, and transverse modulus of elasticity) have not been extensively evaluated. Methods are described for estimating these properties by their relation to other properties.
1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 3737 : 2018 : EDT 1 | Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam) |
| ASTM D 6570 : 2018 : REV A | Standard Practice for Assigning Allowable Properties for Mechanically Graded Lumber |
| ASTM D 2899 : 2012 : R2017 | Standard Practice for Establishing Allowable Stresses for Round Timber Piles |
| ASTM D 5574 : 1994 : R2012 | Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints |
| ASTM D 2395 : 2017 | Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials |
| ASTM D 1990 : 2016 | Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens |
| ASTM D 245 : 2006 : R2011 | Standard Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber |
| ASTM D 5751 : 1999 : R2019 | Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber Products |
| ASTM D 2915 : 2017 | Standard Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products |
| ASTM D 3957 : 2009 : R2015 | Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings |
| ASTM D 2559 : 2012 : REV A : R2018 | Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions |
| ASTM D 25 : 2012 : R2017 | Standard Specification for Round Timber Piles |
| ASTM D 5536 : 2017 | Standard Practice for Sampling Forest Trees for Determination of Clear Wood Properties |
| ASTM D 7381 : 2007 : R2013 | Standard Practice for Establishing Allowable Stresses for Round Timbers for Piles from Tests of Full-Size Material |
| ASTM D 7033 : 2014 | Standard Practice for Establishing Design Capacities for Oriented Strand Board (OSB) Wood-Based Structural-Use Panels |
| ASTM D 9 : 2012 | Standard Terminology Relating to Wood and Wood-Based Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.