ASTM D 2486 : 2017
Current
The latest, up-to-date edition.
Standard Test Methods for Scrub Resistance of Wall Paints
Hardcopy , PDF
English
01-06-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.These test methods cover a procedure for determining the resistance of wall paints to erosion caused by scrubbing, referred to herein after as “scrub resistance.
| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover a procedure for determining the resistance of wall paints to erosion caused by scrubbing, referred to herein after as “scrub resistance.”
1.2Two test methods are covered as follows:
1.2.1Test Method A—Cycles-to-failure obtained on test paint.
1.2.2Test Method B—Ratio expressed as a percentage of cycles-to-failure obtained on the test paint to that obtained on a concurrent run with a known reference paint.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 1797 : 2012 : R2017 : EDT 1 | Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM E 2136 : 2004 : R2013 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Durability (Withdrawn 2022) |
| ASTM F 793/F793M : 2015 | Standard Classification of Wall Coverings by Use Characteristics |
| ASTM D 5324 : 2016 | Standard Guide for Testing Water-Borne Architectural Coatings |
| ASTM D 6736 : 2008 : R2019 | Standard Test Method for Burnish Resistance of Latex Paints |
| ASTM D 6900 : 2010 : R2015 | Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate |
| ASTM D 6763 : 2016 | Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents |
| ASTM D 5146 : 2010 : R2019 | Standard Guide to Testing Solvent-Borne Architectural Coatings |
| ASTM E 1795 : 2017 | Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 3730 : 2017 | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
| ASTM C 744 : 2016 | Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units |
| ASTM D 3924 : 2016 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 4213 : 2008 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 4213 : 2008 : R2016 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 3924 : 1980 : R2011 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 3924 : 1980 : R2005 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 3924 : 2024 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 4213 : 1996 : EDT 1 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 3924 : 1980 : R1996 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 4213 : 2024 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 4213 : 2008 : R2012 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 4213 : 1996 : R2003 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 3924 : 2016 : R2019 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.