ASTM D 2369 : 2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Volatile Content of Coatings
Hardcopy , PDF
11-11-2014
English
10-01-2003
Committee |
D 01
|
DocumentType |
Test Method
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This test method describes a procedure for the determination of the weight percent volatile content of solventborne and waterborne coatings. Test specimens are heated at 110 ± 5°C for 60 min. The coatings used in these round-robin studies represented air-dried, air-dried oxidizing, heat-cured baking systems, and also included multicomponent paint systems.
1.2 Sixty minutes at 110 ± 5—C is a general purpose test method based on the precision obtained with both solventborne and waterborne coatings (see Section 9). These coatings (single package, heat cured) are commonly applied in factories to automobiles, metal containers, flat (coil) metal and large appliances, and many other metal parts.
1.3 This test method is viable for coatings wherein one or more parts may, at ambient conditions, contain liquid coreactants that are volatile until a chemical reaction has occurred with another component of the multi-package system.
Note 1—Committee D01 has run round-robin studies on volatiles of multicomponent paint systems. The only change in procedure is to premix the weighed components in the correct proportions and allow the specimens to stand at room temperature for 1 h prior to placing them into the oven.
1.4 Test Method D 5095 for Determination of the Nonvolatile Content in Silanes, Siloxanes and Silane-Siloxane Blends Used in Masonry Water Repellent Treatments is the standard method for nonvolatile content of these types of materials.
1.5 Test Methods D 5403 for Volatile Content of Radiation Curable Materials is the standard method for determining nonvolatile content of radiation curable coatings, inks and adhesives.
1.6 Test Method D 6419 for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks is the method of choice for these types of printing inks.
1.7 This test method may not be applicable to all types of coatings. Other procedures may be substituted with mutual agreement between the producer and the user.
Note 2—If unusual decomposition or degradation of the specimen occurs during heating, the actual time and temperature used to cure the coating in practice may be substituted for the time and temperature specified in this test method, subject to mutual agreement between the producer and the user. The U.S. EPA Reference Method 24 specifies 110 ± 5°C for 1 h for coatings.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement see 7.4.1.
ASTM D 2832 : 1992 : R2016 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
ASTM D 5201 : 2005 : REV A : R2014 | Standard Practice for Calculating Formulation Physical Constants of Paints and Coatings |
ASTM D 6886 : 2018 | Standard Test Method for Determination of the Weight Percent Individual Volatile Organic Compounds in Waterborne Air-Dry Coatings by Gas Chromatography |
ASTM D 7805 : 2013 | Standard Terminology for Printing Ink Vehicles and Related Materials |
ASTM D 5009 : 2002 : R2017 | Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions |
ASTM D 5403 : 1993 : R2013 | Standard Test Methods for Volatile Content of Radiation Curable Materials |
ASTM F 940 : 1999 : R2013 | Standard Practice for Quality Control Receipt Inspection Procedures for Protective Coatings (Paint), Used in Marine Construction and Shipbuilding |
ASTM D 2698 : 2005 : R2015 | Standard Test Method for Determination of the Pigment Content of Solvent-Reducible Paints by High-Speed Centrifuging |
ASTM D 3960 : 2005 : R2018 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
ASTM D 7232 : 2006 : R2016 | Standard Test Method for Rapid Determination of the Nonvolatile Content of Coatings by Loss in Weight |
ASTM D 7270 : 2007 : R2013 | Standard Guide for Environmental and Performance Verification of Factory-Applied Liquid Coatings |
ASTM D 5324 : 2016 | Standard Guide for Testing Water-Borne Architectural Coatings |
ASTM D 6419 : 2000 : R2017 | Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks |
ASTM C 461 : 2017 | Standard Test Methods for Mastics and Coatings Used With Thermal Insulation |
ASTM D 6093 : 1997 : R2016 | Standard Test Method for Percent Volume Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas Pycnometer |
ASTM D 5327 : 1997 : R2013 | Standard Practice for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under General Laboratory Conditions |
ASTM D 3730 : 2017 | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
ASTM D 5066 : 1991 : R2017 | Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints—Weight Basis |
ASTM D 5087 : 2002 : R2014 | Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
ASTM D 4713 : 2012 | Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems |
ASTM D 2697 : 2003 : R2014 | Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings |
ASTM D 2205 : 2015 | Standard Guide for Selection of Tests for Traffic Paints |
ASTM D 4302 : 2014 | Standard Specification for Artists’ Oil, Resin-Oil, and Alkyd Paints |
ASTM D 5325 : 2003 : R2014 | Standard Test Method for Determination of Weight Percent Volatile Content of Water-Borne Aerosol Paints |
ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
ASTM D 4209 : 2007 : R2019 | Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes |
ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
ASTM D 6763 : 2016 | Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents |
ASTM D 4764 : 2001 : R2016 | Standard Test Method for Determination by X-ray Fluorescence Spectroscopy of Titanium Dioxide Content in Paint |
ASTM C 156 : 2017 | Standard Test Method for Water Loss [from a Mortar Specimen] Through Liquid Membrane-Forming Curing Compounds for Concrete |
ASTM D 6266 : 2000 : REV A : R2017 | Standard Test Method for Determining the Amount of Volatile Organic Compound (VOC) Released From Waterborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
ASTM C 309 : 2011 | Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete |
ASTM D 4143 : 2016 | Standard Guide for Testing Latex Vehicles |
ASTM C 1315 : 2011 | Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete |
ASTM D 6583 : 2013 : R2019 | Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption |
ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
ASTM D 5286 : 2001 : R2017 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.