• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 1742 : 2020

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Oil Separation from Lubricating Grease During Storage

Available format(s)

Hardcopy , PDF

Superseded date

14-11-2024

Superseded by

ASTM D 1742 : 2024

Language(s)

English

Published date

01-05-2020

£57.59
Excluding VAT

Committee
D 02
DocumentType
Test Method
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This test method covers the determination of the tendency of a lubricating grease to separate oil during storage in both normally filled and partially filled containers.

1.2This test method is not suitable for greases softer than NLGI No. 1 grade.

FIG. 1 Pressure Bleeding Test Cell A

 Pressure Bleeding Test Cell A

1.3The values stated in SI units are to be regarded as standard, except for the dimensions in Fig. 2 and Fig. 5, where inch-pound units are standard.

FIG. 2 Detailed Drawing of Pressure Bleeding Test Cell A

 Detailed Drawing of Pressure Bleeding Test Cell A Detailed Drawing of Pressure Bleeding Test Cell A

Note 1:All dimensions are in millimeters (inches).

Note 2:Tolerances are ±0.51 mm (0.02 in.) for 2 place decimals, unless otherwise specified.

Note 3:Tolerances are ±0.127 mm (0.005 in.) for 3 place decimals, unless otherwise specified.

FIG. 3 Pressure Bleeding Test Cell B

 Pressure Bleeding Test Cell B

FIG. 4 Pressure Bleeding Test Cell C

 Pressure Bleeding Test Cell C

FIG. 5 Detailed Drawing of Pressure Bleeding Test Cell C—Strainer Assembly

 Detailed Drawing of Pressure Bleeding Test Cell C—Strainer Assembly Detailed Drawing of Pressure Bleeding Test Cell C—Strainer Assembly

Note 1:All dimensions are in millimeters (inches).

Note 2:Tolerances are ±0.51 mm (0.02 in.) for 2 place decimals, unless otherwise specified.

Note 3:Tolerances are ±0.127 mm (0.005 in.) for 3 place decimals, unless otherwise specified.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see 7.1.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 4732 : 2013 Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable
ASTM D 4950 : 2019 Standard Classification and Specification for Automotive Service Greases
ASTM F 2489 : 2006 : R2013 Standard Guide for Instrument and Precision Bearing Lubricants—Part 2 Greases
ASTM D 4049 : 2016 Standard Test Method for Determining the Resistance of Lubricating Grease to Water Spray
ASTM D 6185 : 2011 : R2017 Standard Practice for Evaluating Compatibility of Binary Mixtures of Lubricating Greases
ASTM D 6184 : 2017 Standard Test Method for Oil Separation from Lubricating Grease (Conical Sieve Method)
ASTM D 4732 : 2013 : R2020 Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable
ASTM D 8324 : 2021 Standard Guide for Selection of Environmentally Acceptable Lubricants for the U.S. Environmental Protection Agency (EPA) Vessel General Permit
ASTM D 4950 : 2022 Standard Classification and Specification for Automotive Service Greases
ASTM D 4049 : 2020 Standard Test Method for Determining the Resistance of Lubricating Grease to Water Spray
ASTM F 2489 : 2006 : R2022 Standard Guide for Instrument and Precision Bearing Lubricants—Part 2 Greases

ASTM E 11 : 2020 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
ASTM E 11 : 2024 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
ASTM E 11 : 2022 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.