ASTM D 1613 : 2017 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products
Available format(s)
PDF
Superseded date
24-02-2017
Language(s)
English
Published date
24-02-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 06.04, 2017 Defines the determination of total acidity as acetic acid, in concentrations below 0.05%, in organic compounds and hydrocarbon mixtures used in paint, varnish, and lacquer solvents and diluents.
| Committee |
D 01
|
| DevelopmentNote |
Supersedes ASTM UOP 809. (10/2010)
|
| DocumentType |
Redline
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| Supersedes |
1.1This test method covers the determination of total acidity as acetic acid, in concentrations below 0.05 %, in organic compounds and hydrocarbon mixtures used in paint, varnish, and lacquer solvents and diluents. It is known to be applicable to such mixtures as low molecular weight saturated and unsaturated alcohols, ketones, ethers, esters, hydrocarbon diluents, naphtha, and other light distillate petroleum fractions.
1.2For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4For specific hazard information and guidance consult supplier’s Safety Data Sheet.
1.5This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 4835 : 2008 : R2012 | Standard Specification for Propylene Glycol Monomethyl Ether Acetate (Withdrawn 2021) |
| ASTM D 4837 : 2007 | Standard Specification for Propylene Glycol Monomethyl Ether |
| BS ISO 4925:2005 | Road vehicles. Specification of non-petroleum-base brake fluids for hydraulic systems |
| MIL I 27686 : F | INHIBITOR, ICING, FUEL SYSTEM |
| ASTM D 3728 : 2008 | Standard Specification for 2-Ethoxyethyl Acetate (99 % Grade) |
| CGSB 15.52 : 1992 | TECHNICAL GRADE METHYL ETHYL KETONE |
| ASTM D 3128 : 2007 : R2013 | Standard Specification for 2-Methoxyethanol |
| A-A-3007 Base Document:1996 | THINNER, FOR PHENOL-FORMALDEHYDE AND MEDIUM OIL AND STYRENATED ALKYD PAINTS AND VARNISHES |
| TT-A-511 Revision E:1992 | AMYL ACETATE, TECHNICAL |
| XP M15 029 : 2006 XP | AUTOMOTIVE FUELS - PETROL-SUPERETHANOL - REQUIREMENTS AND TEST METHODS |
| ASTM E 202 : 2012-06 | TEST METHODS FOR ANALYSIS OF ETHYLENE GLYCOLS AND PROPYLENE GLYCOLS |
| ASTM D 330 : 2007 | Standard Specification for 2-Butoxyethanol |
| ASTM D 3329 : 2003 | Standard Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography |
| ASTM D 2916 : 2009 | Standard Specification for Isophorone |
| ASTM D 4252 : 1989 : R2017 | Standard Test Methods for Chemical Analysis of Alcohol Ethoxylates and Alkylphenol Ethoxylates |
| ASTM D 329 : 2007 : R2013 | Standard Specification for Acetone |
| ASTM D 2634 : 2007 : R2013 | Standard Specification for Methyl Amyl Acetate (95 % Grade) |
| ASTM D 2635 : 2007 : R2012 | Standard Specification for Methyl Isobutyl Carbinol (Withdrawn 2021) |
| ASTM D 5137 : 2007 : R2013 | Standard Specification for Hexyl Acetate |
| ASTM D 2636 : 2007 : R2012 | Standard Specification for Hexylene Glycol (Withdrawn 2021) |
| ASTM D 3893 : 2003 : R2009 | Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography |
| ASTM D 3362 : 2005 | Standard Test Method for Purity of Acrylate Esters by Gas Chromatography (Withdrawn 2011) |
| ASTM D 2636 : 2007 | Standard Specification for Hexylene Glycol |
| ASTM D 2917 : 2007 : R2013 | Standard Specification for Methyl Isoamyl Ketone |
| ASTM D 4773 : 2002 : R2007 | Standard Test Method for Purity of Propylene Glycol Monomethyl Ether, Dipropylene Glycol Monomethyl Ether, and Propylene Glycol Monomethyl Ether Acetate |
| ASTM D 3131 : 2007 : R2013 | Standard Specification for Isopropyl Acetate (99 % Grade) |
| ASTM D 4709 : 2007 : R2012 | Standard Specification for Methyl Acrylate (Withdrawn 2021) |
| CEN/TR 15993:2018 | Automotive fuels - Ethanol (E85) automotive fuel - Background to the parameters required and their respective limits and determination |
| P-W-2891 Revision A:2002 | WIPE SOLVENTS, EXEMPT AND NON-EXEMPT |
| ISO 4925:2005 | Road vehicles Specification of non-petroleum-base brake fluids for hydraulic systems |
| MIL-DTL-27686 Revision G:1997 | INHIBITOR, ICING, FUEL SYSTEM |
| SAE AMS 3166 : 2014 | SOLVENTS, CLEANING, CLEANING PRIOR TO APPLICATION OF SEALING COMPOUNDS |
| ASTM D 319 : 2004 | Standard Specification for Amyl Alcohol (Synthetic) (Withdrawn 2010) |
| ASTM D 4252 : 1989 : R1995 : EDT 1 | Standard Test Methods for Chemical Analysis of Alcohol Ethoxylates and Alkylphenol Ethoxylates |
| O-A-51 Revision H:1992 | ACETONE, TECHNICAL |
| ASTM D 2916 : 2009 : R2017 | Standard Specification for Isophorone |
| CGSB-1.110 : M1991 CORR 1991 | GENERAL PURPOSE THINNER FOR LACQUERS |
| TT-E-781 Revision D:1992 | ETHYLENE GLYCOL MONOETHYL ETHER, TECHNICAL |
| ASTM D 3545 : 2006 | Standard Test Method for Alcohol Content and Purity of Acetate Esters by Gas Chromatography |
| SAE J 1704 : 2016 | MOTOR VEHICLE BRAKE FLUID BASED UPON GLYCOLS, GLYCOL ETHERS AND THE CORRESPONDING BORATES |
| ASTM D 1258 : 2005 | Standard Test Methods for High-Gravity Glycerin (Withdrawn 2011) |
| ASTM D 4836 : 2009 | Standard Specification for Dipropylene Glycol Monomethyl Ether |
| ASTM D 2635 : 2007 | Standard Specification for Methyl Isobutyl Carbinol |
| ASTM D 4709 : 2007 | Standard Specification for Methyl Acrylate |
| ASTM D 2804 : 2002 : R2012 | Standard Test Method for Purity of Methyl Ethyl Ketone By Gas Chromatography (Withdrawn 2021) |
| ASTM D 3329 : 2003 : R2017 | Standard Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography |
| ASTM D 268 : 2001 : R2007 | Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material |
| ASTM D 3585 : 2008 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 3893 : 2003 : R2017 | Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography |
| ASTM D 3585 : 2008 : R2013 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 3548 : 2009 : R2017 | Standard Specification for Ethyl Acrylate |
| ASTM D 1718 : 2009 : R2017 | Standard Specification for Isobutyl Acetate (95 % Grade) |
| ASTM D 268 : 2001 : R2012 | Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material (Withdrawn 2021) |
| ASTM D 608 : 2005 : R2019 | Standard Specification for Dibutyl Phthalate |
| ASTM D 2627 : 2008 : R2012 | Standard Specification for Diacetone Alcohol (Withdrawn 2021) |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| CGSB 1.136 : 1992 | ANTIBLUSH THINNER FOR CELLULOSE NITRATE LACQUER |
| ASTM E 1145 : 1987 : R1992 : EDT 1 | Specification for Denatured Ethyl Alcohol, Formula 3A (Withdrawn 1993) |
| MIL I 85470 : A | INHIBITOR, ICING, FUEL SYSTEM, HIGH FLASH |
| 09/30199323 DC : 0 | BS EN 15293 - AUTOMOTIVE FUELS - ETHANOL (E85) AUTOMOTIVE FUEL REQUIREMENTS AND TEST METHODS |
| ASTM D 608 : 2005 : R2011 | Standard Specification for Dibutyl Phthalate |
| 03/106442 DC : DRAFT APR 2003 | ISO 4925 - ROAD VEHICLES - SPECIFICATION FOR NON-PETROLEUM BASE FLUIDS FOR HYDRAULIC SYSTEMS |
| MIL-PRF-32295 Revision B:2017 | CLEANER, NON-AQUEOUS, LOW-VOC, HAP-FREE |
| ASTM D 5008 : 2007 : R2012 | Standard Test Method for Ethyl Methyl Pentanol Content and Purity Value of 2-Ethylhexanol By Gas Chromatography (Withdrawn 2021) |
| MIL-PRF-32597 Base Document:2018 | CLEANER, POLYMER AND POLYMER MATRIX COMPOSITE (PMC) MATERIAL, NON-AQUEOUS, HAP-FREE |
| ASTM D 4773 : 2002 | Standard Test Method for Purity of Propylene Glycol Monomethyl Ether, Dipropylene Glycol Monomethyl Ether, and Propylene Glycol Monomethyl Ether Acetate |
| ASTM D 4835 : 2008 | Standard Specification for Propylene Glycol Monomethyl Ether Acetate |
| S.R. CEN/TR 15993:2018 | AUTOMOTIVE FUELS - ETHANOL (E85) AUTOMOTIVE FUEL - BACKGROUND TO THE PARAMETERS REQUIRED AND THEIR RESPECTIVE LIMITS AND DETERMINATION |
| CGSB 1.164 : 1999 | SOLVENT FOR VINYL PRETREATMENT COATING |
| ASTM D 3131 :2007 | Standard Specification for Isopropyl Acetate (99 % Grade) |
| ASTM D 2627 : 2008 | Standard Specification for Diacetone Alcohol |
| ASTM D 2804 : 2002 : R2007 | Standard Test Method for Purity of Methyl Ethyl Ketone By Gas Chromatography |
| PD CEN/TR 15993:2013 | Automotive fuels. Ethanol (E85) automotive fuel. Background to the parameters required and their respective limits and determination |
| ASTM D 4615 : 2012 : REDLINE | Standard Specification for n-Butyl Acetate (All Grades) |
| ASTM D 3541 : 2005 | Standard Specification for 2-Ethylhexyl Acrylate |
| DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
| CGSB 15.50 : 1992 | TECHNICAL GRADE ACETONE |
| MIL-DTL-83800 Revision B:2009 | Propanediol, 1, 2- |
| ASTM D 2634 : 2007 | Standard Specification for Methyl Amyl Acetate (95 % Grade) |
| ASTM D 3540 : 2012 : REDLINE | Standard Specification for Primary Amyl Acetate, Synthetic (98 % Grade) |
| SAE J 1703 : 2016 | MOTOR VEHICLE BRAKE FLUID |
| ASTM D 2917 : 2007 | Standard Specification for Methyl Isoamyl Ketone |
| ASTM D 3547 : 2005 | Standard Specification for <i>n</i>-Butyl Acrylate (Withdrawn 2011) |
| ASTM D 329 : 2007 | Standard Specification for Acetone |
| ASTM D 329 : 2007 : EDT 1 | Standard Specification for Acetone <a href="#fn00002"></a> |
| ASTM D 608 : 2005 | Standard Specification for Dibutyl Phthalate |
| ASTM D 5137 :2007 | Standard Specification for Hexyl Acetate |
| ASTM D 5008 : 2007 | Standard Test Method for Ethyl Methyl Pentanol Content and Purity Value of 2-Ethylhexanol By Gas Chromatography |
| ASTM D 3548 : 2009 | Standard Specification for Ethyl Acrylate |
| ASTM D 330 : 2007 : R2013 | Standard Specification for 2-Butoxyethanol |
| ASTM D 3728 : 2008 : R2012 | Standard Specification for 2-Ethoxyethyl Acetate (99 % Grade) (Withdrawn 2021) |
| ASTM D 4252 : 1989 : R2003 | Standard Test Methods for Chemical Analysis of Alcohol Ethoxylates and Alkylphenol Ethoxylates |
| ASTM D 4252 : 1989 : R2009 | Standard Test Methods for Chemical Analysis of Alcohol Ethoxylates and Alkylphenol Ethoxylates |
| GOST 849:2018 | Primary nickel. SpecificationsE |
| ASTM D 4773 : 2002 : R2012 | Standard Test Method for Purity of Propylene Glycol Monomethyl Ether, Dipropylene Glycol Monomethyl Ether, and Propylene Glycol Monomethyl Ether Acetate (Withdrawn 2021) |
| MIL-D-218 Revision B:1981 | DIBUTYL PHTHALATE, TECHNICAL (METRIC) |
| MIL-E-51454 Revision A:1994 | ETHYL ALCOHOL (ETHANOL) |
| ASTM D 3329 : 2003 : R2009 | Standard Test Method for Purity of Methyl Isobutyl Ketone by Gas Chromatography |
| MIL-E-7125 Revision A:1982 | ETHYLENE GLYCOL MONOETHYL ETHER ACETATE, TECHNICAL |
| O-E-760 Revision D:1987 | ETHYL ALCOHOL (ETHANOL), DENATURED ALCOHOL, PROPRIETARY SOLVENTS & SPECIAL INDUSTRIAL SOLVENTS |
| ASTM D 1153 : 2012 : REDLINE | Standard Specification for Methyl Isobutyl Ketone |
| ASTM D 4837 : 2007 : R2012 | Standard Specification for Propylene Glycol Monomethyl Ether (Withdrawn 2021) |
| ASTM F 65 : 1968 : R1983 | Specification for Primary Amyl Acetate (Mixed Isomers) for Use in Fabricating Electron Devices (Withdrawn 1989) |
| ASTM D 363 : 1990 : R2000 | Standard Specification for Tricresyl Phosphate (Withdrawn 2005) |
| SAE AMS 3167 : 2005 | SOLVENTS, WIPE FOR CLEANING PRIOR TO APPLICATION OF PRIMER AND TOP COAT MATERIALS, OR SEALING COMPOUNDS |
| ASTM D 2804 : 2002 | Standard Test Method for Purity of Methyl Ethyl Ketone By Gas Chromatography |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 3893 : 2003 | Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography |
| ASTM E 1177 : 2014 : REDLINE | Standard Specification for Engine Coolant Grade Glycol |
| ASTM D 3128 :2007 | Standard Specification for 2-Methoxyethanol |
| ASTM D 268 : 2001 | Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material |
| ASTM D 4836 : 2009 : R2017 | Standard Specification for Dipropylene Glycol Monomethyl Ether |
| ASTM D 3545 : 2006 : R2012 | Standard Test Method for Alcohol Content and Purity of Acetate Esters by Gas Chromatography (Withdrawn 2021) |
| ASTM D 1718 : 2009 | Standard Specification for Isobutyl Acetate (95% Grade) |
| I.S. CWA 15293:2005 | AUTOMOTIVE FUELS - ETHANOL E85 - REQUIREMENTS AND TEST METHODS |
| ASTM D 7795 : 2015 : REDLINE | Standard Test Method for Acidity in Ethanol and Ethanol Blends by Titration |
| ASTM E 200 : 2016 : REDLINE | Standard Practice for Preparation, Standardization, and Storage of Standard and Reagent Solutions for Chemical Analysis |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.