ASTM D 1319 : 2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
Hardcopy , PDF
11-11-2014
English
01-11-2003
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This test method covers the determination of hydrocarbon types over the concentration ranges from 5 to 99 volume % aromatics, 0.3 to 55 volume % olefins, and 1 to 95 volume % saturates in petroleum fractions that distill below 315°C. This test method may apply to concentrations outside these ranges, but the precision has not been determined. Samples containing dark-colored components that interfere in reading the chromatographic bands cannot be analyzed.
1.2 This test method is intended for use with full boiling range products. Cooperative data have established that the precision statement does not apply to narrow boiling petroleum fractions near the 315°C limit. Such samples are not eluted properly, and results are erratic.
1.3 The applicability of this test method to products derived from fossil fuels other than petroleum, such as coal, shale, or tar sands, has not been determined, and the precision statement may or may not apply to such products.
1.4 This test method has two precision statements depicted in tables. The first table is applicable to unleaded fuels that do not contain oxygenated blending components. It may or may not apply to automotive gasolines containing lead antiknock mixtures. The second table is applicable to oxygenate blended (for example, MTBE, ethanol) automotive spark ignition fuel samples with a concentration range of 13-40 volume percent aromatics, 4-33 volume percent olefins, and 45-68 volume percent saturates.
1.5 The oxygenated blending components, methanol, ethanol, methyl-
1.6 The values stated in SI units are to be regarded as standard.
Note 1—For the determination of olefins below 0.3 volume %, other test methods are available, such as Test Method D 2710.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7, 8.1, and 10.5.
ASTM D 6729 : 2014 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100 Metre Capillary High Resolution Gas Chromatography |
ASTM D 6730 : 2001 : R2016 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100–Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 1655 : 2019 | Standard Specification for Aviation Turbine Fuels |
ASTM D 2425 : 2019 | Standard Test Method for Hydrocarbon Types in Middle Distillates by Mass Spectrometry |
ASTM D 6681 : 2017 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure |
ASTM D 2789 : 1995 : R2016 | Standard Test Method for Hydrocarbon Types in Low Olefinic Gasoline by Mass Spectrometry (Withdrawn 2023) |
ASTM D 3831 : 2012 : R2017 | Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy |
ASTM D 6615 : 2015 : REV A | Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel |
ASTM D 8048 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine |
ASTM D 6987/D6987M : 2013 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine (Withdrawn 2022) |
ASTM D 8147 : 2017 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
ASTM D 7467 : 2019 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 5134 : 2013 : R2017 | Standard Test Method for Detailed Analysis of Petroleum Naphthas through n-Nonane by Capillary Gas Chromatography |
ASTM D 6201 : 2018 : REV A | Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation |
ASTM D 8111 : 2019 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
ASTM D 3735 : 2007 : R2012 | Standard Specification for VM&P Naphthas (Withdrawn 2021) |
ASTM D 6923 : 2018 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure |
ASTM D 8047 : 2018 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
ASTM D 8074 : 2018 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 6709 : 2015 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine) |
ASTM D 5966 : 2013 | Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine (Withdrawn 2022) |
ASTM D 7156 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
ASTM D 6733 : 2001 : R2016 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Metre Capillary High Resolution Gas Chromatography |
ASTM D 3338/D3338M : 2009 : R2014 : EDT 2 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
ASTM D 7566 : 2019 | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
ASTM D 6837 : 2013 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine<rangeref></rangeref > (Withdrawn 2022) |
ASTM D 6894 : 2013 | Standard Test Method for Evaluation of Aeration Resistance of Engine Oils in Direct-Injected Turbocharged Automotive Diesel Engine (Withdrawn 2022) |
ASTM D 7422 : 2017 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4054 : 2019 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
ASTM D 6550 : 2015 | Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography |
ASTM D 3343 : 2016 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
ASTM D 7583 : 2016 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 6750 : 2019 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 5967 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
ASTM D 3734 : 2005 : R2018 | Standard Specification for High-Flash Aromatic Naphthas |
ASTM D 7589 : 2016 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref > |
ASTM D 6618 : 2016 | Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine |
ASTM D 7223 : 2017 | Standard Specification for Aviation Certification Turbine Fuel |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.