ASTM D 1217 : 2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer
Hardcopy , PDF
11-11-2014
English
01-11-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the measurement of the density of pure hydrocarbons or petroleum distillates boiling between 90 and 110°C that can be handled in a normal fashion as a liquid at the specified test temperatures of 20 and 25°C.
1.2This test method provides a calculation procedure for the conversion of density to relative density (specific gravity).
1.3WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Section 7.
| ASTM D 1481 : 2017 | Standard Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Lipkin Bicapillary Pycnometer (Withdrawn 2023) |
| ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 4529 : 2017 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 471 : 2016 : REV A | Standard Test Method for Rubber Property—Effect of Liquids |
| ASTM D 1555M : 2016 | Standard Test Method for Calculation of Volume and Weight of Industrial Aromatic Hydrocarbons and Cyclohexane [Metric] |
| ASTM B 963 : 2017 | Standard Test Methods for Oil Content, Oil-Impregnation Efficiency, and Surface-Connected Porosity of Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle |
| ASTM D 1480 : 2015 | Standard Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Bingham Pycnometer |
| ASTM D 117 : 2018 | Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Liquids |
| ASTM D 2892 : 2018 : REV A | Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column) |
| ASTM D 445 : 2019 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 1405/D1405M : 2008 : R2013 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels (Withdrawn 2019) |
| ASTM C 729 : 2011 : R2016 | Standard Test Method for Density of Glass by the Sink-Float Comparator |
| ASTM D 276 : 2012 | Standard Test Methods for Identification of Fibers in Textiles (Withdrawn 2021) |
| ASTM D 1555 : 2016 | Standard Test Method for Calculation of Volume and Weight of Industrial Aromatic Hydrocarbons and Cyclohexane |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.