• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 1183 : 2003 : R2019

Current

Current

The latest, up-to-date edition.

Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

26-04-2019

£42.23
Excluding VAT

These practices cover the determination of the resistance of adhesives to cyclic accelerated service conditions by exposing bonded specimens to conditions of high and low temperatures and high and low relative humidities.

Committee
D 14
DocumentType
Standard Practice
Pages
3
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1These practices cover the determination of the resistance of adhesives to cyclic accelerated service conditions by exposing bonded specimens to conditions of high and low temperatures and high and low relative humidities. The extent of degradation is determined from changes in strength properties as a result of exposure to the test conditions (Note 1). It is recognized that no accelerated procedure for degrading materials correlates perfectly with actual service conditions, and that no single or small group of laboratory test conditions will simulate all actual service conditions. Consequently, care must be exercised in the interpretation and use of data obtained in this practice. The test condition, the number of cycles of the test condition to be used, the particular strength property to be used to determine the extent of degradation, and whether test specimens or test panels are to be used, are specified in the material specification.

Note 1:These practices/conditions are intended for use with specimens described in the approved ASTM strength test methods for adhesives as follows:

Test Methods D897, D903, D906, D950, D1002, D1062, and Test Method D1344.

1.2The values stated in SI units are to be regarded as the standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 4896 : 2001 : R2016 Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results
ASTM D 7469 : 2016 Standard Test Methods for End-Joints in Structural Wood Products
ASTM D 7793 : 2017 Standard Specification for Insulated Vinyl Siding
ASTM D 6465 : 1999 : R2016 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM D 7793 : 2020 Standard Specification for Insulated Vinyl Siding
ASTM D 7446 : 2009 : R2017 Standard Specification for Structural Insulated Panel (SIP) Adhesives for Laminating Oriented Strand Board (OSB) to Rigid Cellular Polystryene Thermal Insulation Core Materials

ASTM D 1141 : 1998 : R2008 Standard Practice for the Preparation of Substitute Ocean Water
ASTM D 1002 : 1999 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D 1062 : 2008 : R2015 Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds
ASTM D 1141 : 1998 : R2021 Standard Practice for Preparation of Substitute Ocean Water
ASTM D 1141 : 1998 : EDT 1 Standard Practice for the Preparation of Substitute Ocean Water
ASTM D 1062 : 2008 Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds
ASTM D 1002 : 2010 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D 907 : 2015 Standard Terminology of Adhesives
ASTM D 1062 : 1996 : EDT 1 Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds
ASTM D 897 : 2008 : R2016 Standard Test Method for Tensile Properties of Adhesive Bonds
ASTM D 897 : 2008 : R2024 Standard Test Method for Tensile Properties of Adhesive Bonds
ASTM D 1002 : 2005 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D 1141 : 1998 : R2013 Standard Practice for the Preparation of Substitute Ocean Water
ASTM D 907 : 2015 : R2023 Standard Terminology of Adhesives
ASTM D 1344 : 1978 : EDT 1 Methods of Testing Cross-Lap Specimens for Tensile Properties of Adhesives
ASTM D 1002 : 2010 : R2019 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D 1344 : 1978 Methods of Testing Cross-Lap Specimens for Tensile Properties of Adhesives (Withdrawn 1985)
ASTM D 950 : 1998 Standard Test Method for Impact Strength of Adhesive Bonds (Withdrawn 2003)
ASTM D 1002 : 2001 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D 1062 : 2002 Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds
ASTM D 1141 : 1998 : R2003 Standard Practice for the Preparation of Substitute Ocean Water
ASTM D 1062 : 2008 : R2023 Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.