ASTM D 1120 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Boiling Point of Engine Coolants
28-09-2022
English
12-04-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 15.05, 2017 Specifies the determination of the equilibrium boiling point of engine coolants.
| Committee |
D 15
|
| DocumentType |
Redline
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the determination of the equilibrium boiling point of engine coolants. The equilibrium boiling point indicates the temperature at which the sample will start to boil in a cooling system under equilibrium conditions at atmospheric pressure.
Note 1:Engine coolants may also be marketed in a ready-to-use form (prediluted). This test procedure is applicable to diluted solutions as well as to concentrates.
Note 2:The procedure for obtaining a representative test sample of a coolant solution that contains an antileak additive is found in Practice D1176.
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| MIL-A-11755 Revision E:1994 | ANTIFREEZE, ARCTIC-TYPE |
| O-A-548 Revision D:1974 | ANTIFREEZE COOLANT, ENGINE, ETHYLENE GLYCOL, INHIBITED, CONCENTRATED |
| SAE J 814 : 2018 | COOLANTS FOR INTERNAL COMBUSTION ENGINES |
| ASTM D 8085 : 2017 | Standard Specification for Non-Aqueous Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 7518 : 2010 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 3306 : 2014-05 | SPECIFICATION FOR GLYCOL BASE ENGINE COOLANT FOR AUTOMOBILE AND LIGHT-DUTY SERVICE |
| ASTM D 7714 : 2011 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
| MIL-STD-883 Revision K:2016 | TEST METHOD STANDARD - MICROCIRCUITS |
| 09/30163562 DC : DRAFT SEP 2009 | BS 6580 AMD2 - SPECIFICATION FOR CORROSION INHIBITING, ENGINE COOLANT CONCENTRATE ('ANTIFREEZE') |
| BS AU 174-2:1985 | Hydraulic brake systems, using non-petroleum base brake fluids for road vehicles Specification for non-petroleum base brake fluid |
| SAE J 1704 : 2016 | MOTOR VEHICLE BRAKE FLUID BASED UPON GLYCOLS, GLYCOL ETHERS AND THE CORRESPONDING BORATES |
| ASTM D 4656 : 1998 | Standard Specification for Prediluted Aqueous Ethylene Glycol Base Engine Coolant (50 Volume % Minimum) for Automobiles and Light-Duty Service (Withdrawn 2000) |
| ASTM D 3585 : 2008 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 3585 : 2008 : R2013 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 4985 : 2010 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| ISO 4925:2005 | Road vehicles Specification of non-petroleum-base brake fluids for hydraulic systems |
| BS ISO 4925:2005 | Road vehicles. Specification of non-petroleum-base brake fluids for hydraulic systems |
| 03/106442 DC : DRAFT APR 2003 | ISO 4925 - ROAD VEHICLES - SPECIFICATION FOR NON-PETROLEUM BASE FLUIDS FOR HYDRAULIC SYSTEMS |
| ASTM D 5216 : 1998 | Standard Specification for Propylene Glycol Base Engine Coolant for Automobile and Light-Duty Service (Withdrawn 2000) |
| ASTM D 6257 : 1998 | Standard Specification for Prediluted Aqueous Propylene Glycol Base Engine Coolant (50 Volume % Minimum) for Automobile and Light-Duty Service (Withdrawn 2000) |
| ASTM D 5345 : 1998 | Standard Specification for Prediluted Aqueous Ethylene Glycol Base Low-Silicate Engine Coolant (50 Volume % Minimum) for Heavy-Duty Engines Requiring an Initial Charge of Supplemental Coolant Additive (SCA) (Withdrawn 2000) |
| NASA KSC SPEC P 0024 : 2001 | REFRIGERANT, HCFC-124, 2-CHLORO-1,1,1,2-TETRAFLUOROETHANE, SPECIFICATION FOR |
| MIL-STD-750-1 Revision A:2015 | Environmental Test Methods for Semiconductor Devices Part 1: Test Methods 1000 Through 1999 |
| BS 6580:2010 | Specification for corrosion inhibiting, engine coolant concentrate (\'antifreeze\') |
| SAE J 1703 : 2016 | MOTOR VEHICLE BRAKE FLUID |
| ASTM D 7714 : 2011 : R2016 : EDT 1 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
| MIL-A-46153 Revision C:1991 | ANTIFREEZE, ETHYLENE GLYCOL, INHIBITED, HEAVY DUTY, SINGLE PACKAGE |
| A-A-59150 Revision A:1998 | CLEANING COMPOUND, SOLVENT, HYDROFLUOROETHER (HFE) |
| ASTM D 7518 : 2010 : R2015 : EDT 1 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 4985 : 2010 : R2015 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 1176 : 2014 : REDLINE | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.