ASTM D 1101 : 1997 : REV A : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Integrity of Adhesive Joints in Structural Laminated Wood Products for Exterior Use
Hardcopy , PDF
20-09-2024
English
01-08-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 14
|
| DocumentType |
Test Method
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover an accelerated means of measuring the resistance to delamination of structural laminated wood members intended for exterior service.
1.2These test methods are not intended as substitutes or replacements for the more severe test of resistance to delamination in Specification D2559.
1.3Two test methods are included. Choice of test method depends on purpose of the test and available time to complete.
1.3.1Test Method A—This test requires 3 days to complete and is a method for determining the suitability of adhesives and manufacturing techniques and equipment for production of joints adequate for exterior service.
1.3.2Test Method B—This test requires approximately 121/2h. (If excessive delamination occurs, the cycle is repeated). It is a quality-control type test for examining adhesive joint quality.
1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5574 : 1994 : R2012 | Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints |
| ASTM D 7469 : 2016 | Standard Test Methods for End-Joints in Structural Wood Products |
| ASTM D 7966/D7966M : 2016 | Standard Test Method for Resistance to Creep of Adhesives in Static Shear by Compression Loading (Wood-to-Wood) |
| ASTM D 7469 : 2023 | Standard Test Methods for End Joints in Structural Wood Products |
| ASTM D 5574 : 1994 : R2021 | Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints |
| ASTM D 7966/D7966M : 2016 : R2023 | Standard Test Method for Resistance to Creep of Adhesives in Static Shear by Compression Loading (Wood-to-Wood) |
| ASTM D 907 : 2015 | Standard Terminology of Adhesives |
| ASTM D 907 : 2015 : R2023 | Standard Terminology of Adhesives |
| ASTM D 2559 : 2012 : REV A : EDT 1 | Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions |
| ASTM D 2559 : 2000 | Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions |
| ASTM D 2559 : 2012 : REV A : R2018 | Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.