ASTM D 1005 : 1995
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
Hardcopy , PDF
11-11-2014
English
01-01-2001
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 06.01, 2017 Outlines the measurements of film thickness of dried films of paint, lacquer, varnish and associated products using micrometers.
| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
3
|
| ProductNote |
Reconfirmed 1995
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This test method covers the measurement of film thickness of dried films of paint, varnish, lacquer, and related products using micrometers. Procedures A and B utilize stationary micrometers and Procedures C and D, hand-held micrometers. Procedures A and C are not recommended for films less than 0.5 mils (12.5 µm) in thickness. The minimum thickness required for Procedures B and D is a function of that required to enable removal of the sample as a free film.
1.2 The procedures appear as follows:
1.2.1 Procedure A--Stationary micrometer for measuring coatings applied to plane rigid surfaces.
1.2.2 Procedure B--Stationary micrometer for measuring free films.
1.2.3 Procedure C--Hand-held micrometer for measuring coatings applied to plane rigid surfaces.
1.2.4 Procedure D --Hand-held micrometer for measuring free films.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM D 5178 : 2016 | Standard Test Method for Mar Resistance of Organic Coatings |
| ASTM E 1797 : 2012 : R2017 : EDT 1 | Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM A 1003/A1003M : 2015 | Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members |
| ASTM D 2091 : 1996 : R2017 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 3170/D3170M : 2014 | Standard Test Method for Chipping Resistance of Coatings |
| ASTM D 4060 : 2014 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 1653 : 2013 | Standard Test Methods for Water Vapor Transmission of Organic Coating Films |
| ASTM D 7394 : 2018 | Standard Practice for Rheological Characterization of Architectural Coatings using Three Rotational Bench Viscometers |
| ASTM D 6037 : 2018 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
| ASTM A 978/A978M : 2008 : R2013 | Standard Specification for Composite Ribbed Steel Pipe, Precoated and Polyethylene Lined for Gravity Flow Sanitary Sewers, Storm Sewers, and Other Special Applications (Withdrawn 2020) |
| ASTM A 755/A755M : 2018 | Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products |
| ASTM D 2197 : 2016 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 4587 : 2011 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings |
| ASTM D 5087 : 2002 : R2014 | Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
| ASTM D 4366 : 2016 | Standard Test Methods for Hardness of Organic Coatings by Pendulum Damping Tests |
| ASTM D 333 : 2001 : R2013 | Standard Guide for Clear and Pigmented Lacquers |
| ASTM D 6669 : 2019 | Standard Practice for Selecting and Constructing Exposure Scenarios for Assessment of Exposures to Alkyd and Latex Interior Paints |
| ASTM D 5286 : 2001 : R2017 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
| ASTM D 3730 : 2017 | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
| ASTM D 823 : 2018 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM D 6442 : 2006 : R2012 | Standard Test Method for Determination of Copper Release Rate From Antifouling Coatings in Substitute Ocean Water |
| ASTM D 6486 : 2001 : R2017 | Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings |
| ASTM D 2134 : 1993 : R2012 | Standard Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker |
| ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 6903 : 2007 : R2013 | Standard Test Method for Determination of Organic Biocide Release Rate From Antifouling Coatings in Substitute Ocean Water |
| ASTM E 1796 : 2003 : R2016 | Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 5498 : 2012 : REV A : R2018 | Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities |
| ASTM D 2248 : 2001 : REV A : R2018 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 4138 : 2007 : REV A : R2017 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM A 849 : 2015 | Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe |
| ASTM D 5895 : 2013 | Standard Test Methods for Evaluating Drying or Curing During Film Formation of Organic Coatings Using Mechanical Recorders |
| ASTM D 6803 : 2013 | Standard Practice for Testing and Sampling of Volatile Organic Compounds (Including Carbonyl Compounds) Emitted from Paint Using Small Environmental Chambers |
| ASTM D 5590 : 2017 | Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Fungal Defacement by Accelerated Four-Week Agar Plate Assay |
| ASTM D 968 : 2017 | Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive |
| ASTM D 6695 : 2016 | Standard Practice for Xenon-Arc Exposures of Paint and Related Coatings |
| ASTM C 1349 : 2017 | Standard Specification for Architectural Flat Glass Clad Polycarbonate |
| ASTM D 6132 : 2013 : R2017 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 2370 : 2016 | Standard Test Method for Tensile Properties of Organic Coatings |
| ASTM D 522/D522M : 2017 | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| ASTM D 2803 : 2009 : R2015 | Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal |
| ASTM D 7187 : 2015 | Standard Test Method for Measuring Mechanistic Aspects of Scratch/Mar Behavior of Paint Coatings by Nanoscratching |
| ASTM F 3078 : 2015 | Standard Test Method for Identification and Quantification of Lead in Paint and Similar Coating Materials using Energy Dispersive X-ray Fluorescence Spectrometry (EDXRF) |
| ASTM D 6279 : 2015 | Standard Test Method for Rub Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 4708 : 2012 | Standard Practice for Preparation of Uniform Free Films of Organic Coatings |
| ASTM A 762/A762M : 2015 | Standard Specification for Corrugated Steel Pipe, Polymer Precoated for Sewers and Drains |
| ASTM D 3322 : 1982 : R2017 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 6762 : 2018 | Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings |
| ASTM E 1795 : 2017 | Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM D 7377 : 2009 : R2018 | Standard Practice for Evaluating the Water Wash-Off Resistance of Traffic Paints using a Water Faucet |
| ASTM A 742/A742M : 2018 | Standard Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 7538 : 2009 : R2018 | Standard Practice for Evaluating the Water Wash-Off Resistance of Traffic Paints Using an Atomizing Spray Device |
| ASTM D 3361/D3361M : 2013 : R2018 | Standard Practice for Unfiltered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings |
| ASTM D 5031/D5031M : 2013 : R2018 | Standard Practice for Enclosed Carbon-Arc Exposure Tests of Paint and Related Coatings |
| ASTM D 822/D822M : 2013 : R2018 | Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings |
| ASTM D 2454 : 2018 | Standard Practice for Determining the Effect of Overbaking on Organic Coatings |
| ASTM D 1474/D1474M : 2013 : R2018 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM D 2370 : 2016 : REDLINE | Standard Test Method for Tensile Properties of Organic Coatings |
| ASTM D 823 : 1995 | Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.