ASTM D 1002 : 2010 : R2019
Current
Current
The latest, up-to-date edition.
Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-04-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.
| Committee |
D 14
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4054 : 2019 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
| ASTM D 3164 : 2003 : R2017 | Standard Test Method for Strength Properties of Adhesively Bonded Plastic Lap-Shear Sandwich Joints in Shear by Tension Loading |
| ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM D 2294 : 1996 : R2016 | Standard Test Method for Creep Properties of Adhesives in Shear by Tension Loading (Metal-to-Metal) |
| ASTM D 6412/D6412M : 1999 : R2012 | Standard Specification For Epoxy (Flexible) Adhesive For Bonding Metallic And Nonmetallic Materials |
| ASTM D 1828 : 2001 : R2013 | Standard Practice for Atmospheric Exposure of Adhesive-Bonded Joints and Structures |
| ASTM D 3163 : 2001 : R2014 | Standard Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading |
| ASTM D 4896 : 2001 : R2016 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 2919 : 2001 : R2014 | Standard Test Method for Determining Durability of Adhesive Joints Stressed in Shear by Tension Loading |
| ASTM D 1338 : 1999 : R2016 | Standard Practice for Working Life of Liquid or Paste Adhesives by Consistency and Bond Strength |
| ASTM D 1780 : 2005 : R2012 | Standard Practice for Conducting Creep Tests of Metal-to-Metal Adhesives |
| ASTM D 3930 : 2008 : R2015 | Standard Specification for Adhesives for Wood-Based Materials for Construction of Manufactured Homes |
| ASTM E 1555 : 2012 | Standard Specification for Structural Paste Adhesive for Sandwich Panel Repair |
| ASTM D 2293 : 1996 : R2016 | Standard Test Method for Creep Properties of Adhesives in Shear by Compression Loading (Metal-to-Metal) |
| ASTM D 3658 : 2001 : R2016 | Standard Test Method for Determining the Torque Strength of Ultraviolet (UV) Light-Cured Glass/Metal Adhesive Joints |
| ASTM E 1826 : 2012 | Standard Specification for Low Volatile Organic Compound (VOC) Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded |
| ASTM D 6465 : 1999 : R2016 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| ASTM D 7826 : 2019 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
| ASTM F 2468 : 2005 : R2019 | Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications |
| ASTM E 1800 : 2013 | Standard Specification for Adhesive for Bonding Foam Cored Sandwich Panels (160°F Elevated Humidity Service), Type I Panels |
| ASTM D 3166 : 1999 : R2012 | Standard Test Method for Fatigue Properties of Adhesives in Shear by Tension Loading (Metal/Metal) |
| ASTM D 2295 : 1996 : R2016 | Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading at Elevated Temperatures (Metal-to-Metal) |
| ASTM E 865 : 2012 | Standard Specification for Structural Film Adhesives for Honeycomb Sandwich Panels |
| ASTM D 1337 : 2010 : R2016 | Standard Practice for Storage Life of Adhesives by Viscosity and Bond Strength |
| ASTM D 1151 : 2000 : R2013 | Standard Practice for Effect of Moisture and Temperature on Adhesive Bonds |
| ASTM D 1144 : 1999 : R2016 | Standard Practice for Determining Strength Development of Adhesive Bonds |
| ASTM D 2093 : 2003 : R2017 | Standard Practice for Preparation of Surfaces of Plastics Prior to Adhesive Bonding |
| ASTM D 5868 : 2001 : R2014 | Standard Test Method for Lap Shear Adhesion for Fiber Reinforced Plastic (FRP) Bonding |
| ASTM E 866 : 2019 | Standard Specification for Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels |
| ASTM D 896 : 2004 : R2017 | Standard Practice for Resistance of Adhesive Bonds to Chemical Reagents |
| ASTM D 6411/D6411M : 1999 : R2012 | Standard Specification For Silicone Rubber Room Temperature Vulcanizing Low Outgassing Materials |
| ASTM D 1183 : 2003 : R2019 | Standard Practices for Resistance of Adhesives to Cyclic Laboratory Aging Conditions |
| ASTM D 2557 : 1998 : R2017 | Standard Test Method for Tensile-Shear Strength of Adhesives in the Subzero Temperature Range from −267.8 to −55°C (−450 to −67°F) |
| ASTM E 1794 : 2013 | Standard Specification for Adhesive for Bonding Foam Cored Sandwich Panels (200°F Elevated Humidity Service), Type II Panels |
| SAE AIR6291A:2024 | Guidelines for Repair Process Evaluation of Aluminum Bonded Structure |
| ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM A 109/A109M : 2024 | Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled |
| ASTM B 36/B36M : 2018 | Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar |
| ASTM B 209 : 2014 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM D 4896 : 2001 : R2008 : EDT 1 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 4896 : 2001 : R2024 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 4896 : 1995 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 907 : 2015 | Standard Terminology of Adhesives |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4896 : 2001 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM A 109/A109M : 2016 : R2018 | Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM B 152/B152M : 2024 | Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar |
| ASTM B 36/B36M : 2023 | Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar |
| ASTM D 907 : 2015 : R2023 | Standard Terminology of Adhesives |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM B 265 : 2005 : EDT 1 | Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate |
| ASTM B 152/B152M : 2019 | Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM A 109/A109M : 1998 : REV A | Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled |
| ASTM D 4896 : 2001 : R2016 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM E 4 : 2024 | Standard Practices for Force Calibration and Verification of Testing Machines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.