ASTM C 67/C67M : 2021
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile
Hardcopy , PDF
12-07-2023
English
22-06-2021
Committee |
C 15
|
DocumentType |
Test Method
|
Pages |
17
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing, efflorescence, initial rate of absorption and determination of weight, size, warpage, length change, and void area. (Additional methods of test pertinent to ceramic glazes include imperviousness, chemical resistance, opacity, and resistance to crazing.
1.2The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
Note 1:The testing laboratory performing this test method should be evaluated in accordance with Practice C1093.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.4These test methods include the following sections:
Section Heading | Section |
Scope | 1 |
Referenced Documents | 2 |
Terminology | 3 |
Sampling | 4 |
Specimen Preparation | 5 |
Modulus of Rupture (Flexure Test) | 6 |
Compressive Strength | 7 |
Absorption | 8 |
Freezing and Thawing | 9 |
Initial Rate of Absorption (Suction) (Laboratory Test) | 10 |
Efflorescence | 11 |
Weight Per Unit Area | 12 |
Measurement of Size | 13 |
Measurement of Warpage | 14 |
Measurement of Length Change | 15 |
Initial Rate of Absorption (Suction) (Field Test) | 16 |
Measurement of Void Area in Cored Units | 17 |
Measurement of Void Area in Deep Frogged Units | 18 |
Measurement of Out of Square | 19 |
Measurement of Shell and Web Thickness | 20 |
Breaking Load | 21 |
Imperviousness Test (of Ceramin Glazes) | 22 |
Chemical Resistance Test (of Ceramic Glazes) | 23 |
Autoclaved Crazing Test (of Ceramic Glazes) | 24 |
Opacity Test (of Ceramic Glazes) | 25 |
Precision and Bias | 26 |
Keywords | 27 |
Safety Precautions for Autoclave Equipment and Operation | Appendix X1 |
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 1232 : 2020 | Standard Terminology for Masonry |
ASTM C 1791 : 2016 : R2021 | Standard Guide for Reduction of Efflorescence Potential in New Unit Pavement Systems |
ASTM C 126 : 2019 | Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units |
ASTM C 652 : 2019 : REV B | Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale) |
ASTM C 1568 : 2008 : R2020 | Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Mechanical Uplift Resistance Method) |
ASTM E 2260 : 2021 | Standard Guide for Repointing (Tuckpointing) Historic Masonry |
ASTM E 2266 : 2011 : R2019 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
ASTM C 1093 : 2019 | Standard Practice for Accreditation of Testing Agencies for Masonry |
ASTM E 519/E519M : 2020 | Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages |
ASTM C 1587/C1587M : 2021 | Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Testing |
ASTM C 1405 : 2020 : REV A | Standard Specification for Glazed Brick (Single Fired, Brick Units) |
ASTM C 1072 : 2019 | Standard Test Methods for Measurement of Masonry Flexural Bond Strength |
ASTM D 6684 : 2018 | Standard Specification for Materials and Manufacture of Articulating Concrete Block (ACB) Systems |
ASTM C 902 : 2020 | Standard Specification for Pedestrian and Light Traffic Paving Brick |
ASTM C 1088 : 2020 | Standard Specification for Thin Veneer Brick Units Made From Clay or Shale |
ASTM C 1314 : 2018 | Standard Test Method for Compressive Strength of Masonry Prisms |
ASTM E 3069 : 2019 : REV A | Standard Guide for Evaluation and Rehabilitation of Mass Masonry Walls for Changes to Thermal and Moisture Properties of the Wall |
ASTM C 315 : 2007 : R2021 | Standard Specification for Clay Flue Liners and Chimney Pots |
ASTM C 1208/C1208M : 2018 | Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling, Sliplining, Pipe Bursting, and Tunnels |
ASTM C 902 : 2022 | Standard Specification for Pedestrian and Light Traffic Paving Brick |
ASTM E 519/E519M : 2022 | Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages |
ASTM E 754 : 1980 : R2022 | Standard Test Method for Pullout Resistance of Ties and Anchors Embedded in Masonry Mortar Joints |
ASTM C 1272 : 2022 : REV A | Standard Specification for Heavy Vehicular Paving Brick |
ASTM C 126 : 2022 | Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units |
ASTM C 216 : 2022 | Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale) |
ASTM E 2266 : 2022 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
ASTM C 1405 : 2023 | Standard Specification for Glazed Brick (Single Fired, Brick Units) |
ASTM C 1261 : 2022 | Standard Specification for Firebox Brick for Residential Fireplaces |
ASTM C 1569 : 2022 | Standard Test Method for Wind Resistance of Concrete and Clay Roof Tiles (Wind Tunnel Method) |
ASTM C 1072 : 2022 | Standard Test Methods for Measurement of Masonry Flexural Bond Strength |
ASTM C 530 : 2023 | Standard Specification for Structural Clay Nonloadbearing Screen Tile |
ASTM C 1492 : 2022 | Standard Specification for Concrete Roof Tile |
ASTM C 1167 : 2022 | Standard Specification for Clay Roof Tiles |
ASTM C 56 : 2022 | Standard Specification for Structural Clay Nonloadbearing Tile |
ASTM E 518/E518M : 2022 | Standard Test Methods for Flexural Bond Strength of Masonry |
ASTM C 652 : 2022 | Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale) |
ASTM C 1208/C1208M : 2018 : R2022 | Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling, Sliplining, Pipe Bursting, and Tunnels |
ASTM E 2260 : 2021 : REV A | Standard Guide for Repointing (Tuckpointing) Historic Masonry |
ASTM C 1587/C1587M : 2021 : REV A | Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Testing |
ASTM C 1314 : 2023 | Standard Test Method for Compressive Strength of Masonry Prisms |
ASTM C 1232 : 2020 | Standard Terminology for Masonry |
ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM C 1093 : 2022 | Standard Practice for Accreditation of Testing Agencies for Masonry |
ASTM C 1232 : 2021 | Standard Terminology for Masonry |
ASTM C 150/C150M : 2020 | Standard Specification for Portland Cement |
ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
ASTM C 1232 : 2021 : REV A | Standard Terminology for Masonry |
ASTM C 1093 : 2022 : REV A | Standard Practice for Accreditation of Testing Agencies for Masonry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.