ASTM C 465 : 2022
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Processing Additions for Use in the Manufacture of Hydraulic Cements
Hardcopy , PDF
04-08-2023
English
26-07-2022
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
C 01
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification pertains to the criteria and tests to be used for determining whether a(n) organic or inorganic processing addition, when used in the recommended amount at the option of the cement producer in the manufacture of hydraulic cements, meets the requirements as prescribed by definition in Specifications C150/C150M, C1157/C1157M, C845/C845M, and C595/C595M. The materials listed in the following former ASTM Specifications shall be considered as meeting the organic processing additions requirements of this specification:
| C150/C150M – 62, for Portland Cement | ||
| C205 – 58 T, for Portland Blast-Furnace Slag Cement | ||
| C340 – 58 T, for Portland Pozzolan Cement | ||
| C358 – 58, for Slag Cement | ||
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 688 : 2022 | Standard Specification for Functional Additions for Use in Hydraulic Cements |
| ASTM C 989/C989M : 2022 | Standard Specification for Slag Cement for Use in Concrete and Mortars |
| ASTM C 845/C845M : 2018 | Standard Specification for Expansive Hydraulic Cement |
| ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
| ASTM C 563 : 2020 | Standard Guide for Approximation of Optimum SO<inf>3</inf> in Hydraulic Cement |
| ASTM C 10/C10M : 2019 | Standard Specification for Natural Cement |
| ASTM C 989/C989M : 2018 : REV A | Standard Specification for Slag Cement for Use in Concrete and Mortars |
| ASTM C 688 : 2014 | Standard Specification for Functional Additions for Use in Hydraulic Cements |
| ASTM C 138/C138M : 2014 | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
| ASTM C 173/C173M : 2014 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
| ASTM C 231/C231M : 2017 : REV A | Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 191 : 2019 | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
| ASTM C 231/C231M : 2014 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
| ASTM C 226 : 2019 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM C 185 : 2015 : REV A | Standard Test Method for Air Content of Hydraulic Cement Mortar |
| ASTM C 187 : 2023 | Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste |
| ASTM C 191 : 2018 : REV A | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
| ASTM C 226 : 2022 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM C 39/C39M : 2015 : REV A | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 109/C109M : 2020 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
| ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
| ASTM C 204 : 2023 | Standard Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus |
| ASTM C 39/C39M : 2020 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 143/C143M : 2015 : REV A | Standard Test Method for Slump of Hydraulic-Cement Concrete |
| ASTM C 109/C109M : 2016 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
| ASTM C 39/C39M : 2018 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 204 : 2018 : EDT 1 | Standard Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus |
| ASTM C 187 : 2016 | Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste |
| ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
| ASTM C 114 : 2018 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
| ASTM C 231/C231M : 2022 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
| ASTM C 114 : 2022 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.