ASTM C 387/C387M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
Hardcopy , PDF
23-08-2023
English
22-12-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This specification covers the production, properties, packaging, and testing of packaged, dry, combined materials for concrete and high strength mortar.
| Committee |
C 09
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the production, properties, packaging, and testing of packaged, dry, combined materials for concrete and high strength mortar. The classifications of concrete and mortar covered are defined in Section 3.
Note 1:The scope of this standard does not cover mortars for unit masonry. Dry preblended mortars for unit masonry are covered by Specification C1714/C1714M.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Some values have only SI units because the inch-pound equivalents are not used in practice.
1.3The following safety hazards caveat pertains only to the test method portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1581/C1581M : 2018 : REV A | Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage |
| ASTM G 210 : 2013 : R2023 | Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus |
| ASTM C 1600/C1600M : 2023 | Standard Specification for Rapid Hardening Hydraulic Cement |
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1437 : 2001 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 1240 : 2001 | Standard Specification for Use of Silica Fume for Use as a Mineral Admixture in Hydraulic-Cement Concrete, Mortar, and Grout |
| ASTM C 138/C138M : 2014 | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
| ASTM C 173/C173M : 2014 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
| ASTM C 173/C173M : 2009 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
| ASTM C 494/C494M : 2019 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 494/C494M : 2019 : EDT 1 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 1240 : 2010 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 305 : 2014 | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
| ASTM C 1600/C1600M : 2019 | Standard Specification for Rapid Hardening Hydraulic Cement |
| ASTM C 39/C39M : 2021 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 1437 : 2013 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 1329 : 2003 : REV A | Standard Specification for Mortar Cement |
| ASTM C 192/C192M : 2000 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
| ASTM C 1240 : 2014 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 185 : 2015 : REV A | Standard Test Method for Air Content of Hydraulic Cement Mortar |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1240 : 2004 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 1329 : 2000 | Standard Specification for Mortar Cement |
| ASTM C 1116 : 2002 | Standard Specification for Fiber-Reinforced Concrete and Shotcrete |
| ASTM C 1157 : 2002 | Standard Performance Specification for Hydraulic Cement |
| ASTM C 1240 : 2000 : EDT 1 | Standard Specification for Use of Silica Fume for Use as a Mineral Admixture in Hydraulic-Cement Concrete, Mortar, and Grout |
| ASTM C 1329 : 2004 | Standard Specification for Mortar Cement |
| ASTM C 1157 : 2003 | Standard Performance Specification for Hydraulic Cement |
| ASTM C 39/C39M : 2015 : REV A | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 618 : 2023 : EDT 1 | Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
| ASTM C 1240 : 2010 : REV A | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 1438 : 2011 : REV A | Standard Specification for Latex and Powder Polymer Modifiers in Hydraulic Cement Concrete and Mortar |
| ASTM C 109/C109M : 2020 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
| ASTM C 1116 : 2000 | Standard Specification for Fiber-Reinforced Concrete and Shotcrete |
| ASTM C 39/C39M : 2020 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 1240 : 2012 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 1240 : 2003 | Standard Specification for Use of Silica Fume for Use as a Mineral Admixture in Hydraulic-Cement Concrete, Mortar, and Grout |
| ASTM C 618 : 2022 | Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
| ASTM C 1438 : 1999 : R2005 : EDT 1 | Standard Specification for Latex and Powder Polymer Modifiers for Hydraulic Cement Concrete and Mortar |
| ASTM C 143/C143M : 2015 : REV A | Standard Test Method for Slump of Hydraulic-Cement Concrete |
| ASTM C 618 : 2023 | Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
| ASTM C 1438 : 1999 : EDT 1 | Standard Specification for Latex and Powder Polymer Modifiers for Hydraulic Cement Concrete and Mortar |
| ASTM C 1157 : 2000 : REV A | Standard Performance Specification for Hydraulic Cement |
| ASTM C 1157 : 2008 : REV A | Standard Performance Specification for Hydraulic Cement |
| ASTM C 109/C109M : 2016 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
| ASTM C 1116 : 2003 | Standard Specification for Fiber-Reinforced Concrete and Shotcrete |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1438 : 2013 | Standard Specification for Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
| ASTM C 39/C39M : 2018 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 494/C494M : 2010 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 1437 : 2007 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 618 : 2019 | Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
| ASTM C 1329 : 2005 | Standard Specification for Mortar Cement |
| ASTM C 33 : 1985 | Standard Specification for Concrete Aggregates |
| ASTM C 330 : 2000 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1437 : 2015 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 1240 : 2015 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 1240 : 2020 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 1157 : 2008 | Standard Performance Specification for Hydraulic Cement |
| ASTM C 150 : 2002 : REV A : EDT 1 | Standard Specification for Portland Cement |
| ASTM C 1438 : 2011 | Standard Specification for Latex and Powder Polymer Modifiers in Hydraulic Cement Concrete and Mortar |
| ASTM C 1240 : 2011 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 1437 : 1999 | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 330 : 1999 | Standard Specification for Lightweight Aggregates For Structural Concrete |
| ASTM C 1329 : 2003 | Standard Specification for Mortar Cement |
| ASTM C 1240 : 2005 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| ASTM C 1438 : 2013 : R2017 | Standard Specification for Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
| ASTM C 1240 : 2003 : REV A | Standard Specification for Use of Silica Fume for Use as a Mineral Admixture in Hydraulic-Cement Concrete, Mortar, and Grout |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.