ASTM C 1583 : 2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
Hardcopy , PDF
11-11-2014
English
01-02-2004
CONTAINED IN VOL 04.02, 2005
Committee |
C 09
|
DocumentType |
Test Method
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1 This test method is suitable for both field and laboratory use to determine one or more of the following:
1.1.1 The near-surface tensile strength of the substrate as an indicator of the adequacy of surface preparation before application of a repair or overlay material.
1.1.2 The bond strength of a repair or an overlay material to the substrate.
1.1.3 The tensile strength of a repair or overlay material, or an adhesive used in repairs, after the material has been applied to a surface.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
AASHTO TP 96 : 2013 | METHOD OF TEST FOR PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE |
ASTM D 7234 : 2012 : REDLINE | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
CTI ESG 123 : 2012 | RECOMMENDED GUIDELINES FOR CONCRETE RESTORATION AND REPAIRS TO NATURAL AND MECHANICAL DRAFT COOLING TOWERS |
ACI 548.9 : 2008 | SPECIFICATION FOR TYPE ES (EPOXY SLURRY) POLYMER OVERLAYS FOR BRIDGE AND PARKING GARAGE DECKS |
ACI 548.8 : 2007 | SPECIFICATION FOR TYPE EM (EPOXY MULTI-LAYER) POLYMER OVERLAY FOR BRIDGE AND PARKING GARAGE DECKS |
ACI 548.8M : 2007 | SPECIFICATION FOR TYPE EM (EPOXY MULTI-LAYER) POLYMER OVERLAY FOR BRIDGE AND PARKING GARAGE DECKS |
ASTM F 3010 : 2013 | Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings |
ACI 325.13R : 2006 | CONCRETE OVERLAYS FOR PAVEMENT REHABILITATION |
AASHTO TP 96 : 2013 (R2018) | METHOD OF TEST FOR PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE |
ASTM F 2873 : 2013 | Standard Practice for the Installation of Self-Leveling Underlayment and the Preparation of Surface to Receive Resilient Flooring |
ACI 548.9M : 2008 | SPECIFICATION FOR TYPE ES (EPOXY SLURRY) POLYMER OVERLAY FOR BRIDGE AND PARKING GARAGE DECKS |
ASTM F 2873 : 2018 | Standard Practice for the Installation of Self-Leveling Underlayment and the Preparation of Surface to Receive Resilient Flooring |
ASTM F 3010 : 2018 | Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings |
ASTM D 7234 : 2012 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
ACI 207.6R : 2017 | REPORT ON THE EROSION OF CONCRETE IN HYDRAULIC STRUCTURES |
ASTM C 900 : 2015 : REDLINE | Standard Test Method for Pullout Strength of Hardened Concrete |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.