ASTM C 1582/C1582M : 2011 : R2017 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete
Hardcopy , PDF
26-09-2024
English
15-06-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL 04.02, 2017 Specifies material for use as chloride-corrosion-inhibiting admixtures for concrete.
| Committee |
C 09
|
| DocumentType |
Standard
|
| Pages |
10
|
| ProductNote |
Reconfirmed EDT 1
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers material for use as chloride-corrosion-inhibiting admixtures for concrete.
1.2Results of the tests conducted to meet this specification are not to be used to rank the expected field performance of various chloride-corrosion-inhibiting admixtures.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 2480 : 2018 : R2024 | Standard Guide for In-ground Concrete Skatepark |
| ASTM C 39/C39M : 2024 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 150/C150M : 2024 | Standard Specification for Portland Cement |
| ASTM C 403/C403M : 2016 : REDLINE | Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance |
| ASTM C 494/C494M : 2019 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 494/C494M : 2019 : EDT 1 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 231/C231M : 2017 : REV A | Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
| ASTM G 109 : 2021 | Standard Test Methods for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments |
| ASTM C 150/C150M : 2017-04 | SPECIFICATION FOR PORTLAND CEMENT |
| ASTM C 39/C39M : 2021 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 78/C78M : 2021 | Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading) |
| ASTM C 231/C231M : 2014 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
| ASTM C 39/C39M : 2023 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 78/C78M : 2016 | Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading) |
| ACI 211.1 : 1991 | SELECTING PROPORTIONS FOR NORMAL, HEAVYWEIGHT AND MASS CONCRETE |
| ASTM C 157/C157M : 2017 | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
| ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 231/C231M : 2024 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
| ASTM C 39/C39M : 2015 : REV A | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
| ASTM C 39/C39M : 2020 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM C 666/C666M : 2015 : REDLINE | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing |
| ASTM C 403/C403M : 2023 | Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance |
| ASTM G 180 : 2013 : REDLINE | TEST METHOD FOR CORROSION INHIBITING ADMIXTURES FOR STEEL IN CONCRETE BY POLARIZATION RESISTANCE IN CEMENTITIOUS SLURRIES |
| ASTM C 143/C143M : 2015 : REV A | Standard Test Method for Slump of Hydraulic-Cement Concrete |
| ASTM G 180 : 2023 | Standard Test Method for Corrosion Inhibiting Admixtures for Steel in Concrete by Polarization Resistance in Cementitious Slurries |
| ASTM C 157/C157M : 2024 | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
| ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM G 109 : 2007 : R2013 | Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments |
| ASTM C 39/C39M : 2018 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
| ASTM G 180 : 2013 : R2019 | Standard Test Method for Corrosion Inhibiting Admixtures for Steel in Concrete by Polarization Resistance in Cementitious Slurries |
| ASTM C 494/C494M : 2010 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 78/C78M : 2018 | Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading) |
| ASTM C 157/C157M : 2017 : REDLINE | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
| ASTM C 666/C666M : 2015 | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing (Withdrawn 2024) |
| ASTM C 403/C403M : 2016 | Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance |
| ASTM C 494/C494M : 2024 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 150/C150M : 2020 | Standard Specification for Portland Cement |
| ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 494/C494M : 2017 : REDLINE | Standard Specification for Chemical Admixtures for Concrete |
| ASTM G 109 : 2023 | Standard Test Methods for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments |
| ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
| ASTM C 78/C78M : 2022 | Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading) |
| ASTM C 231/C231M : 2022 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
| ASTM G 180 : 2021 | Standard Test Method for Corrosion Inhibiting Admixtures for Steel in Concrete by Polarization Resistance in Cementitious Slurries |
| ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.