ASTM C 157/C157M : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete
21-08-2024
English
15-08-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.02, 2017 Defines the determination of the length changes that are produced by causes other than externally applied forces and temperature changes in hardened hydrauliccement mortar and concrete specimens made in the laboratory and exposed to controlled conditions of temperature and moisture.
| Committee |
C 09
|
| DevelopmentNote |
Supersedes ASTM C 157 (07/2006)
|
| DocumentType |
Redline
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the determination of the length changes that are produced by causes other than externally applied forces and temperature changes in hardened hydraulic-cement mortar and concrete specimens made in the laboratory and exposed to controlled conditions of temperature and moisture.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E11. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1709 : 2011 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
| ACI 360R : 2010 | GUIDE TO DESIGN OF SLABS-ON-GROUND |
| ASTM C 928/C928M : 2013 : REDLINE | Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs |
| ACI 325.14R : 2017 | GUIDE FOR DESIGN AND PROPORTIONING OF CONCRETE MIXTURES FOR PAVEMENTS |
| ASTM C 596 : 2009 : R2017 | Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement |
| ASTM C 1708/C1708M : 2016 : REDLINE | Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements |
| ASTM C 1293 : 2008 : REV B : R2015 | Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction |
| ASTM C 1582/C1582M : 2011 : R2017 : EDT 1 | Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete |
| ASTM C 1293 : 2008 : REV A | Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction |
| ASTM C 1698 : 2009 | Standard Test Method for Autogenous Strain of Cement Paste and Mortar |
| ASTM C 1107/C1107M : 2017 : REDLINE | Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink) |
| AASHTO TP 96 : 2013 (R2018) | METHOD OF TEST FOR PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE |
| AASHTO TP 110 : 2014 | METHOD OF TEST FOR POTENTIAL ALKALI REACTIVITY OF AGGREGATES AND EFFECTIVENESS OF ASR MITIGATION MEASURES (MINIATURE CONCRETE PRISM TEST, MCPT) |
| ASTM C 596 : 2009 | Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement |
| MIL-DTL-32536 Base Document:2015 | CONCRETE CAPPING MATERIAL, RAPID SETTING |
| ASTM C 596 : 2009 : EDT 1 | Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement |
| ACI 351.1R : 2012 | REPORT ON GROUTING BETWEEN FOUNDATIONS AND BASES FOR SUPPORT OF EQUIPMENT & MACHINERY |
| ACI 301 : 2016 | SPECIFICATIONS FOR STRUCTURAL CONCRETE |
| ACI SP 307 : 2016 | SHRINKAGE COMPENSATING CONCRETE - PAST, PRESENT, AND FUTURE |
| ASTM C 183/C183M : 2016 : REDLINE | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
| ASTM C 1105 : 2008 : REV A : R2016 | Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction |
| ASTM C 330 : 2005 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 331/C331M : 2017 : REDLINE | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
| ASTM C 331 : 2005 | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
| ASTM C 1107 : 2007 | SPECIFICATION FOR PACKAGED DRY, HYDRAULIC-CEMENT GROUT (NONSHRINK) |
| ASTM C 1148 : 1992 : REV A : R1997 : EDT 1 | Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar |
| ASTM C 1622/C1622M : 2010 : R2016 : EDT 1 | Standard Specification for Cold-Weather Admixture Systems |
| ASTM C 1148 : 1992 : REV A : R2014 | Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar (Withdrawn 2019) |
| UFC 3-301-01 : Change 3 | UNIFIED FACILITIES CRITERIA - STRUCTURAL ENGINEERING |
| ASTM C 1148 : 1992 : REV A : R2008 | Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar |
| ACI 301M : 2016 | SPECIFICATIONS FOR STRUCTURAL CONCRETE |
| ACI 303R : 2012 | GUIDE TO CAST-IN-PLACE ARCHITECTURAL CONCRETE PRACTICE |
| ACI 364.3R : 2009 | GUIDE FOR CEMENTITIOUS REPAIR MATERIAL DATA SHEET |
| ACI ITG-8R : 2010 | REPORT ON PERFORMANCE-BASED REQUIREMENTS FOR CONCRETE |
| ACI 223R : 2010 | GUIDE FOR THE USE OF SHRINKAGE-COMPENSATING CONCRETE |
| AASHTO T 127 : 2015 | METHOD OF TEST FOR SAMPLING AND AMOUNT OF TESTING OF HYDRAULIC CEMENT |
| ASTM C 1792 : 2014 | Standard Test Method for Measurement of Mass Loss versus Time for One-Dimensional Drying of Saturated Concretes (Withdrawn 2023) |
| ASTM C 1856/C1856M : 2017 | Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete |
| ASTM C 1698 : 2009 : R2014 | Standard Test Method for Autogenous Strain of Cement Paste and Mortar |
| ASTM C 494/C494M : 2017 : REDLINE | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 1731 : 2016 : REDLINE | Standard Specification for Concrete Floor Tile |
| ASTM C 1105 : 2008 | Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction |
| ASTM C 1622/C1622M : 2010 | Standard Specification for Cold-Weather Admixture Systems |
| AASHTO TP 96 : 2013 | METHOD OF TEST FOR PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE |
| ASTM C 688 : 2014 : REDLINE | Standard Specification for Functional Additions for Use in Hydraulic Cements |
| ASTM C 1293 : 2008 : REV B | Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction |
| ASTM C 341/C341M : 2014-01 | PRACTICE FOR PREPARATION AND CONDITIONING OF CAST, DRILLED, OR SAWED SPECIMENS OF HYDRAULIC-CEMENT MORTAR AND CONCRETE USED FOR LENGTH CHANGE MEASUREMENTS |
| ACI PRC-506 : 2016 | GUIDE TO SHOTCRETE |
| UFC 4-150-07 : Change 1 | UNIFIED FACILITIES CRITERIA - MAINTENANCE AND OPERATION: MAINTENANCE OF WATERFRONT FACILITIES |
| ACI 237R : 2007 | SELF-CONSOLIDATING CONCRETE |
| CSA A3000 : 2013 | CEMENTITIOUS MATERIALS COMPENDIUM |
| ASTM C 1012 : 2004 | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
| ASTM C 806 : 2013-02 | TEST METHOD FOR RESTRAINED EXPANSION OF EXPANSIVE CEMENT MORTAR |
| ASTM C 1148 : 1992 : REV A : R2002 | Standard Test Method for Measuring the Drying Shrinkage of Masonry Mortar |
| ASTM C 1105 : 2008 : REV A | Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction |
| ASTM C 666/C666M : 2015 : REDLINE | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing |
| ASTM C 1582/C1582M : 2011 | Standard Specification for Admixtures to Inhibit Chloride-Induced Corrosion of Reinforcing Steel in Concrete |
| ACI 330.2R:2017(R2023) | Guide for the Design and Construction of Concrete Site Paving for Industrial and Trucking Facilities |
| CSA A23.1 A23.2 : 2014 | CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE |
| ASTM C 1437 : 2015 : REDLINE | Standard Test Method for Flow of Hydraulic Cement Mortar |
| ASTM C 305 : 2014 : REDLINE | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
| ASTM C 192/C192M : 2016-04 | PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY |
| ASTM E 337 : 2015 : REDLINE | Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures) |
| ASTM E 11 : 2017 : REDLINE | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.