ASTM C 144 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Aggregate for Masonry Mortar
Hardcopy , PDF
02-01-2025
English
01-12-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.1 This specification covers aggregate for use in masonry mortar.
| Committee |
C 15
|
| DocumentType |
Standard
|
| Pages |
3
|
| ProductNote |
THIS STANDARD ALSO REFERS-C88/C88M
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers aggregate for use in masonry mortar.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3The following precautionary caveat pertains only to the test methods portion, Section 8, of this standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ACI PRC-549.3:2022 | Glass Fiber-Reinforced Concrete Premix—Report |
| ASTM C 1660 : 2010 : R2018 | Standard Specification for Thin-bed Mortar for Autoclaved Aerated Concrete (AAC) Masonry |
| ASTM C 1384 : 2023 | Standard Specification for Admixtures for Masonry Mortars |
| ASTM C 627 : 2018 : EDT 1 | Standard Test Method for Evaluating Ceramic Floor Tile Installation Systems Using the Robinson-Type Floor Tester |
| ASTM E 754 : 1980 : R2022 | Standard Test Method for Pullout Resistance of Ties and Anchors Embedded in Masonry Mortar Joints |
| ASTM C 1714/C1714M : 2023 | Standard Specification for Preblended Dry Mortar Mix for Unit Masonry |
| ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
| ASTM E 2992/E2992M : 2017 | Standard Test Method for Evaluating Response Robot Mobility: Traverse Sand Terrain |
| ASTM C 387/C387M : 2023 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
| ASTM C 1324 : 2020 : REV A | Standard Test Method for Examination and Analysis of Hardened Masonry Mortar |
| ASTM C 1586 : 2020 | Standard Guide for Quality Assurance of Mortars |
| ASTM C 1314 : 2023 : REV B | Standard Test Method for Compressive Strength of Masonry Prisms |
| ASTM C 1693 : 2011 : R2017 | Standard Specification for Autoclaved Aerated Concrete (AAC) |
| ASTM E 2853/E2853M : 2022 | Standard Test Method for Evaluating Ground Response Robot Capabilities: Search Tasks |
| ASTM C 627 : 2018 : R2024 | Standard Test Method for Evaluating Ceramic Floor Tile Installation Systems Using the Robinson-Type Floor Tester |
| ACI CODE-350:2020 | Code Requirements for Environmental Engineering Concrete Structures (ACI 350-20) and Commentary (ACI 350R-20)<br> |
| ASTM C 1180 : 2010 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 40/C40M : 2011 | Standard Test Method for Organic Impurities in Fine Aggregates for Concrete |
| ASTM C 117 : 2017 | Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing |
| ASTM C 123/C123M : 2023 | Standard Test Method for Lightweight Particles in Aggregate |
| ASTM C 270 : 1919 : REV A : EDT 1 | Standard Specification for Mortar for Unit Masonry |
| ASTM C 1713 : 2023 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 1180 : 2003 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 1180 : 2024 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 142/C142M : 2017 : R2023 | Standard Test Method for Clay Lumps and Friable Particles in Aggregates |
| ASTM C 1180 : 2002 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 1713 : 2017 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 1713 : 2015 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 40/C40M : 2020 | Standard Test Method for Organic Impurities in Fine Aggregates for Concrete |
| ASTM C 142/C142M : 2017 | Standard Test Method for Clay Lumps and Friable Particles in Aggregates |
| ASTM C 40/C40M : 2019 | Standard Test Method for Organic Impurities in Fine Aggregates for Concrete |
| ASTM C 1713 : 2024 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 1713 : 2010 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 1180 : 2018 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 1180 : 2003 : REV A : EDT 1 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 404 : 2024 | Standard Specification for Aggregates for Masonry Grout |
| ASTM C 87/C87M : 2017 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
| ASTM D 75/D75M : 2009 | Standard Practice for Sampling Aggregates |
| ASTM C 87/C87M : 2023 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
| ASTM C 136/C136M : 2014 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
| ASTM C 1180 : 2003 : REV A | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 1180 : 2022 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 117 : 2023 | Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing |
| ASTM C 128 : 2015 | Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate |
| ASTM D 75/D75M : 2014 | Standard Practice for Sampling Aggregates |
| ASTM C 88/C88M : 2018 | Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate |
| ASTM C 1713 : 2012 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 1180 : 2007 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 123/C123M : 2014 | Standard Test Method for Lightweight Particles in Aggregate (Withdrawn 2023) |
| ASTM C 1713 : 2011 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 404 : 1997 | Standard Specification for Aggregates for Masonry Grout |
| ASTM C 1180 : 2019 | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 404 : 2018 | Standard Specification for Aggregates for Masonry Grout |
| ASTM C 1180 : 2000 : REV A | Standard Terminology of Mortar and Grout for Unit Masonry |
| ASTM C 270 : 2024 | Standard Specification for Mortar for Unit Masonry |
| ASTM C 88/C88M : 2024 | Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate |
| ASTM C 128 : 2022 | Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.