ASTM C 109/C109M : 2021
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens)
Hardcopy , PDF
15-05-2024
English
12-08-2021
Committee |
C 01
|
DocumentType |
Test Method
|
Pages |
12
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers determination of the compressive strength of hydraulic cement mortars, using 2-in. or [50mm] cube specimens.
Note 1:Test Method C349 provides an alternative procedure for this determination (not to be used for acceptance tests).
1.2This test method covers the application of the test using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI-10, of measurements made in other units.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E 519/E519M : 2021 | Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages |
ASTM C 1451 : 2018 | Standard Practice for Determining Variability of Concrete-Making Materials From a Single Source |
ASTM C 349 : 2018 | Standard Test Method for Compressive Strength of Hydraulic-Cement Mortars<brk/> (Using Portions of Prisms Broken in Flexure) |
ASTM D 6532 : 2000 : R2014 | Standard Test Method for Evaluation of the Effect of Clear Water Repellent Treatments on Water Absorption of Hydraulic Cement Mortar Specimens |
ASTM C 452 : 2021 | Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate |
ASTM C 465 : 2019 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
ASTM A 1096/A1096M : 2015 | Standard Test Method for Evaluating Bond of Individual Steel Wire, Indented or Plain, for Concrete Reinforcement |
ASTM C 617/C617M : 2015 | Standard Practice for Capping Cylindrical Concrete Specimens |
ASTM C 1602/C1602M : 2018 | Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete |
ASTM E 754 : 1980 : R2014 : EDT 1 | Standard Test Method for Pullout Resistance of Ties and Anchors Embedded in Masonry Mortar Joints |
ASTM F 2718 : 2009 : R2015 | Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines (Withdrawn 2022) |
ASTM C 778 : 2017 | Standard Specification for Standard Sand |
ASTM C 1439 : 2019 | Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
ASTM C 1709 : 2018 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
ASTM C 348 : 2021 | Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars |
ASTM C 10/C10M : 2019 | Standard Specification for Natural Cement |
ASTM F 2719 : 2009 : R2015 | Standard Practice for Installation of Polyethylene (PE) and Encapsulated Cement Mortar Formed in Place Lining System (FIPLS) for the Rehabilitation of Water Pipelines (Withdrawn 2022) |
ASTM C 1260 : 2021 | Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method) |
ASTM C 183/C183M : 2016 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
ASTM F 2678 : 2016 | Standard Practice for Preparing Panel Underlayments, Thick Poured Gypsum Concrete Underlayments, Thick Poured Lightweight Cellular Concrete Underlayments, and Concrete Subfloors with Underlayment Patching Compounds to Receive Resilient Flooring |
ASTM C 226 : 2019 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
ASTM C 1093 : 2019 | Standard Practice for Accreditation of Testing Agencies for Masonry |
ASTM C 807 : 2020 | Standard Test Method for Time of Setting of Hydraulic Cement Mortar by Modified Vicat Needle |
ASTM C 780 : 2020 | Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
ASTM C 939/C939M : 2016 : REV A | Standard Test Method for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone Method) |
ASTM C 932 : 2006 : R2019 | Standard Specification for Surface-Applied Bonding Compounds for Exterior Plastering |
ASTM D 5860 : 1995 : R2013 | Standard Test Method for Evaluation of the Effect of Water Repellent Treatments on Freeze-Thaw Resistance of Hydraulic Cement Mortar Specimens |
ASTM C 110 : 2020 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
ASTM C 688 : 2014 | Standard Specification for Functional Additions for Use in Hydraulic Cements |
ASTM C 806 : 2018 | Standard Test Method for Restrained Expansion of Expansive Cement Mortar |
ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
ASTM C 563 : 2020 | Standard Guide for Approximation of Optimum SO<inf>3</inf> in Hydraulic Cement |
ASTM C 1216/C1216M : 2013 | Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants (Withdrawn 2022) |
ASTM C 1600/C1600M : 2019 | Standard Specification for Rapid Hardening Hydraulic Cement |
ASTM C 1713 : 2017 | Standard Specification for Mortars for the Repair of Historic Masonry |
ASTM C 845/C845M : 2018 | Standard Specification for Expansive Hydraulic Cement |
ASTM C 719 : 2014 : R2019 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
ASTM C 802 : 2014 | Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials |
ASTM C 1074 : 2019 : EDT 1 | Standard Practice for Estimating Concrete Strength by the Maturity Method |
ASTM C 1328/C1328M : 2019 : REDLINE | Standard Specification for Plastic (Stucco) Cement |
ASTM D 5759 : 2012 : R2020 | Standard Guide for Characterization of Coal Fly Ash and Clean Coal Combustion Fly Ash for Potential Uses |
ASTM C 1240 : 2020 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
ASTM D 1734 : 1993 : R2013 | Standard Practice for Making Cementitious Panels for Testing Coatings |
ASTM C 1247 : 2020 | Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids |
ASTM C 1329/C1329M : 2016 : REV A | Standard Specification for Mortar Cement |
ASTM D 8329 : 2021 | Standard Test Method for Determination of Water/Cementitious Materials Ratio for Geosynthetic Cementitious Composite Mats (GCCMs) and Measurement of the Compression Strength of the Cementitious Material Contained Within |
ASTM C 87/C87M : 2017 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
ASTM C 1403 : 2015 | Standard Test Method for Rate of Water Absorption of Masonry Mortars |
ASTM C 1506 : 2017 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
ASTM C 387/C387M : 2017 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
ASTM F 3010 : 2018 | Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings |
ASTM C 91/C91M : 2018 | Standard Specification for Masonry Cement |
ASTM C 1803 : 2020 | Standard Guide for Abrasion Resistance of Mortar Surfaces Using a Rotary Platform Abraser |
ASTM C 311/C311M : 2018 | Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete |
ASTM C 928/C928M : 2020 : REV A | Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs |
ASTM A 1081/A1081M : 2021 | Standard Test Method for Evaluating Bond of Seven-Wire Steel Prestressing Strand |
ASTM D 4796 : 2017 | Standard Test Method for Bond Strength of Thermoplastic Pavement Marking Materials |
ASTM C 942/C942M : 2021 | Standard Test Method for Compressive Strength of Grouts for Preplaced-Aggregate Concrete in the Laboratory |
ASTM C 141/C141M : 2014 | Standard Specification for Hydrated Hydraulic Lime for Structural Purposes |
ASTM C 1707 : 2018 | Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes |
ASTM C 1157/C1157M : 2020 : REV A | Standard Performance Specification for Hydraulic Cement |
ASTM F 1741 : 2018 | Standard Practice for Installation of Machine Spiral Wound Poly (Vinyl Chloride) (PVC) Liner Pipe for Rehabilitation of Existing Sewers and Conduits |
ASTM E 2322 : 2003 : R2015 | Standard Test Method for Conducting Transverse and Concentrated Load Tests on Panels used in Floor and Roof Construction |
ASTM D 5050 : 2008 : R2015 | Standard Guide for Commercial Use of Lime Kiln Dusts and Portland Cement Kiln Dusts |
ASTM C 1107/C1107M : 2020 | Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink) |
ASTM C 441/C441M : 2017 | Standard Test Method for Effectiveness of Pozzolans or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction |
ASTM D 6449 : 1999 : R2015 : EDT 1 | Standard Test Method for Flow of Fine Aggregate Concrete for Fabric Formed Concrete (Flow Cone Method) (Withdrawn 2024) |
ASTM C 1708/C1708M : 2019 | Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements |
ASTM C 1437 : 2020 | Standard Test Method for Flow of Hydraulic Cement Mortar |
ASTM C 1222 : 2021 | Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement |
ASTM C 917/C917M : 2018 | Standard Test Method for Evaluation of Variability of Cement from a Single Source Based on Strength |
ASTM C 1073 : 2018 | Standard Test Method for Hydraulic Activity of Slag Cement by Reaction with Alkali |
ASTM F 2551 : 2009 : R2016 | Standard Practice for Installing a Protective Cementitious Liner System in Sanitary Sewer Manholes |
ASTM C 901 : 2018 | Standard Specification for Prefabricated Masonry Panels |
ASTM C 882/C882M : 2020 | Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete By Slant Shear |
ASTM F 710 : 2021 | Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring |
ASTM C 989/C989M : 2018 : REV A | Standard Specification for Slag Cement for Use in Concrete and Mortars |
ASTM C 1012/C1012M : 2018 : REV B | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
ASTM E 1266 : 2020 | Standard Practice for Processing Mixtures of Lime, Fly Ash, and Heavy Metal Wastes in Structural Fills and Other Construction Applications |
ASTM C 1038/C1038M : 2019 | Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water |
ASTM C 185 : 2020 | Standard Test Method for Air Content of Hydraulic Cement Mortar |
ASTM C 1567 : 2021 | Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method) |
ASTM C 495/C495M : 2012 : R2019 | Standard Test Method for Compressive Strength of Lightweight Insulating Concrete |
ASTM C 510 : 2016 | Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants |
ASTM F 2985 : 2014 : R2019 | Standard Practice for Installation of a PVC Segmental Panel Liner System in Man-Entry Size Sewers and Conduits (Withdrawn 2024) |
ASTM C 719 : 2022 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
ASTM F 2678 : 2016 : R2021 | Standard Practice for Preparing Panel Underlayments, Thick Poured Gypsum Concrete Underlayments, Thick Poured Lightweight Cellular Concrete Underlayments, and Concrete Subfloors with Underlayment Patching Compounds to Receive Resilient Flooring |
ASTM D 1734 : 1993 : R2022 | Standard Practice for Making Cementitious Panels for Testing Coatings |
ASTM C 1602/C1602M : 2022 | Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete |
ASTM C 778 : 2021 | Standard Specification for Standard Sand |
ASTM D 6532 : 2000 : R2022 | Standard Test Method for Evaluation of the Effect of Clear Water Repellent Treatments on Water Absorption of Hydraulic Cement Mortar Specimens |
ASTM C 510 : 2016 : R2022 | Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants |
ASTM C 141/C141M : 2014 : R2022 | Standard Specification for Hydrated Hydraulic Lime for Structural Purposes |
ASTM D 5860 : 1995 : R2022 | Standard Test Method for Evaluation of the Effect of Water Repellent Treatments on Freeze-Thaw Resistance of Hydraulic Cement Mortar Specimens |
ASTM C 311/C311M : 2022 | Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete |
ASTM C 1093 : 2022 | Standard Practice for Accreditation of Testing Agencies for Masonry |
ASTM C 807 : 2021 | Standard Test Method for Time of Setting of Hydraulic Cement Mortar by Modified Vicat Needle |
ASTM C 311/C311M : 2024 | Standard Test Methods for Sampling and Testing Coal Ash or Natural Pozzolans for Use in Concrete |
ASTM C 1012/C1012M : 2024 | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
ASTM C 989/C989M : 2024 | Standard Specification for Slag Cement for Use in Concrete and Mortars |
ASTM C 882/C882M : 2023 | Standard Test Method for Bond Strength of Bonding Systems Used With Concrete By Slant Shear |
ASTM C 1038/C1038M : 2024 | Standard Test Method for Expansion of Hydraulic Cementitious Material Mortar Bars Stored in Water |
ASTM C 1708/C1708M : 2023 | Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements |
ASTM A 981/A981M : 2023 | Standard Test Method for Evaluating Bond Strength for 0.600-in. [15.24-mm] Diameter Seven-Wire Steel Strand, Grade 270 [1860], Used in Prestressed Ground Anchors |
ASTM E 519/E519M : 2022 | Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages |
ASTM C 1073 : 2018 : R2023 | Standard Test Method for Hydraulic Activity of Slag Cement by Reaction with Alkali |
ASTM C 183/C183M : 2023 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
ASTM E 754 : 1980 : R2022 | Standard Test Method for Pullout Resistance of Ties and Anchors Embedded in Masonry Mortar Joints |
ASTM C 939/C939M : 2022 | Standard Test Method for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone Method) |
ASTM F 710 : 2022 | Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring |
ASTM D 5050 : 2008 : R2023 | Standard Guide for Commercial Use of Lime Kiln Dusts and Portland Cement Kiln Dusts |
ASTM C 87/C87M : 2023 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
ASTM C 1260 : 2023 | Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method) |
ASTM C 1567 : 2023 | Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method) |
ASTM C 1713 : 2023 | Standard Specification for Mortars for the Repair of Historic Masonry |
ASTM C 802 : 2014 : R2022 | Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials |
ASTM C 617/C617M : 2023 | Standard Practice for Capping Cylindrical Concrete Specimens |
ASTM C 226 : 2022 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
ASTM C 1803/C1803M : 2023 | Standard Guide for Abrasion Resistance of Mortar Surfaces Using a Rotary Platform Abraser |
ASTM C 806 : 2023 | Standard Test Method for Restrained Expansion of Expansive Cement Mortar |
ASTM C 688 : 2022 | Standard Specification for Functional Additions for Use in Hydraulic Cements |
ASTM C 1216/C1216M : 2023 | Standard Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants |
ASTM C 465 : 2023 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
ASTM C 780 : 2023 | Standard Test Methods for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
ASTM F 2551 : 2009 : R2023 | Standard Practice for Installing a Protective Cementitious Liner System in Sanitary Sewer Manholes |
ASTM C 1600/C1600M : 2023 | Standard Specification for Rapid Hardening Hydraulic Cement |
ASTM D 4796 : 2017 : R2022 | Standard Test Method for Bond Strength of Thermoplastic Pavement Marking Materials |
ASTM C 1093 : 2023 | Standard Practice for Accreditation of Testing Agencies for Masonry |
ASTM C 1403 : 2022 : REV A | Standard Test Method for Rate of Water Absorption of Masonry Mortars |
ASTM C 387/C387M : 2023 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
ASTM C 10/C10M : 2024 | Standard Specification for Natural Cement |
ASTM F 1741 : 2022 | Standard Practice for Installation of Machine Spiral Wound Poly (Vinyl Chloride) (PVC) Liner Pipe for Rehabilitation of Existing Sewers and Conduits |
ASTM A 1096/A1096M : 2022 | Standard Test Method for Evaluating Bond of Individual Steel Wire, Indented or Plain, for Concrete Reinforcement |
ASTM C 1928/C1928M : 2023 | Standard Test Method for Compressive Strength of Alkali Activated Cementitious Material Mortars (Using 2-in. [50 mm] Cube Specimens) |
ASTM C 1910/C1910M : 2023 | Standard Test Methods for Cements that Require Carbonation Curing |
ASTM C 1866/C1866M : 2022 | Standard Specification for Ground-Glass Pozzolan for Use in Concrete |
ASTM C 1222 : 2023 | Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement |
ASTM F 3010 : 2018 : R2024 | Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings |
ASTM C 1709 : 2022 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
ASTM C 511 : 2021 | Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes |
ASTM C 230/C230M : 2021 | Standard Specification for Flow Table for Use in Tests of Hydraulic Cement |
ASTM C 305 : 2014 | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
ASTM C 91/C91M : 2023 | Standard Specification for Masonry Cement |
ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
ASTM C 1157/C1157M : 2023 | Standard Performance Specification for Hydraulic Cement |
ASTM C 989/C989M : 2018 : REV A | Standard Specification for Slag Cement for Use in Concrete and Mortars |
ASTM C 618 : 2023 : EDT 1 | Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
ASTM C 1328/C1328M : 2023 | Standard Specification for Plastic (Stucco) Cement |
ASTM C 511 : 2019 | Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes |
ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
ASTM C 778 : 2017 | Standard Specification for Standard Sand |
ASTM C 618 : 2022 | Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
ASTM C 618 : 2023 | Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
ASTM C 1329/C1329M : 2023 | Standard Specification for Mortar Cement |
ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
ASTM C 114 : 2023 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
ASTM C 595/C595M : 2023 | Standard Specification for Blended Hydraulic Cements |
ASTM C 1328/C1328M : 2019 | Standard Specification for Plastic (Stucco) Cement |
ASTM C 618 : 2019 | Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
ASTM C 1437 : 2015 | Standard Test Method for Flow of Hydraulic Cement Mortar |
ASTM C 989/C989M : 2022 | Standard Specification for Slag Cement for Use in Concrete and Mortars |
ASTM C 230/C230M : 2023 | Standard Specification for Flow Table for Use in Tests of Hydraulic Cement |
ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
ASTM C 670 : 2015 | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
ASTM C 114 : 2018 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
ASTM C 114 : 2022 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
ASTM C 778 : 2021 | Standard Specification for Standard Sand |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.