ASTM B 36/B36M : 2023
Current
The latest, up-to-date edition.
Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar
Hardcopy , PDF
English
11-10-2023
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
B 05
|
| DocumentType |
Standard
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification establishes the requirements for brass (copper-zinc alloy) plate, sheet, strip, and rolled bar of the following alloys:
| Copper Alloy | Type of Metal |
| C21000 | Gilding |
| C22000 | Commerical Bronze |
| C22600 | Jewerly Bronze |
| C23000 | Red Brass |
| C24000 | Low Brass |
| C26000 | Cartridge Brass |
| C26800 | Yellow Brass |
| C27200 | … |
| C28000 | Muntz Metal |
1.2Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.3.1This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM B 315 : 2019 | Standard Specification for Seamless Copper Alloy Pipe and Tube |
| ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM D 3433 : 1999 : R2020 | Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints |
| ASTM F 1387 : 2023 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
| ASTM F 1144 : 2019 | Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight, Hinged |
| ASTM D 3528 : 1996 : R2016 | Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading |
| ASTM D 4054 : 2023 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
| ASTM F 1018 : 2022 | Standard Specification for Steel Emergency Gear Stowage Locker |
| ASTM D 5363 : 2016 | Standard Specification for Anaerobic Single-Component Adhesives (AN) |
| ASTM F 1142 : 2019 | Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight |
| ASTM D 1002 : 2010 : R2019 | Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal) |
| ASTM B 248M : 2022 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
| ASTM D 8040 : 2018 : R2023 | Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware |
| ASTM B 248 : 2022 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
| ASTM D 1384 : 2005 : R2019 | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
| ASTM D 3658 : 2001 : R2016 | Standard Test Method for Determining the Torque Strength of Ultraviolet (UV) Light-Cured Glass/Metal Adhesive Joints |
| ASTM B 927/B927M : 2017 | Standard Specification for Brass Rod, Bar, and Shapes |
| ASTM F 992 : 2017 : R2022 | Standard Specification for Valve Label Plates |
| ASTM D 3165 : 2007 : R2023 | Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies |
| ASTM F 1974 : 2023 | Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe |
| ASTM F 1143 : 2019 | Standard Specification for Manhole Cover Assembly, Bolted, Raised, Oiltight and Watertight |
| ASTM E 8/E8M : 2024 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM B 846 : 2019 : REV A | Standard Terminology for Copper and Copper Alloys |
| ASTM E 478 : 2024 | Standard Test Methods for Chemical Analysis of Copper Alloys |
| ASTM B 846 : 2024 | Standard Terminology for Copper and Copper Alloys |
| ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 478 : 2008 : R2017 | Standard Test Methods for Chemical Analysis of Copper Alloys |
| ASTM E 112 : 2013 : R2021 | Standard Test Methods for Determining Average Grain Size |
| ASTM B 601 : 2024 | Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast |
| ASTM B 601 : 2018 : REV A | Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast |
| ASTM E 112 : 2024 | Standard Test Methods for Determining Average Grain Size |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.