ASTM B 122/B122M : 2016 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar
Available format(s)
PDF
Superseded date
15-10-2020
Superseded by
Language(s)
English
Published date
01-04-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 02.01, 2017 Describes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar.
| Committee |
B 05
|
| DevelopmentNote |
Supersedes QQ C 585 (07/2004)
|
| DocumentType |
Redline
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar. The following alloys are covered:
| Nominal Composition, % | ||||||
| Copper Alloy | Previously Used | Chro- | ||||
| UNS No.2 | Designation | Copper | Nickel | Zinc | Tin | mium |
| C70600 | ... | 90 | 10 | ... | ... | ... |
| C70620 | ... | 90 | 10 | ... | ... | ... |
| C71000 | 6 | 80 | 20 | ... | ... | ... |
| C71500 | 5 | 70 | 30 | ... | ... | ... |
| C71520 | ... | 70 | 30 | ... | ... | ... |
| C72200 | ... | 85 | 15 | ... | ... | 0.5 |
| C72500 | ... | 89 | 9 | ... | 2 | ... |
| C73500 | 1 | 72 | 18 | 10 | ... | ... |
| C74000 | 9 | 70 | 10 | 20 | ... | ... |
| C74500 | 3 | 65 | 10 | 25 | ... | ... |
| C75200 | 2 | 65 | 18 | 17 | ... | ... |
| C76200 | 8 | 59 | 12 | 29 | ... | ... |
| C77000 | 4 | 55 | 18 | 27 | ... | ... |
Note 1:Plates of copper-nickel alloy Copper Alloy UNS Nos. C70600, C70620, C71500, C71520, and C72200 for use as tube plates in surface condensers and heat exchangers are covered by Specification B171/B171M.
1.2Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
| MIL-DTL-83734 Revision H:2007 | SOCKETS, PLUG-IN ELECTRONIC COMPONENTS, DUAL-IN-LINE (DIPS) AND SINGLE-IN-LINE PACKAGES (SIPS), GENERAL SPECIFICATION FOR |
| ASTM F 96 : 1977 : R2010 | Standard Specification for Electronic Grade Alloys of Copper and Nickel in Wrought Forms |
| MIL-DTL-83503 Revision C:2005 | Connectors, Electrical, Flat Cable, and/or Printed Wiring Board, Nonenvironmental General Specification for |
| A-A-55469 Revision B:2015 | CONNECTORS, ELECTRICAL, PLUGS, TIP (TEST POINT PLUG, BANANA PLUG) GENERAL REQUIREMENTS FOR |
| MIL V 13612 : E | VALVE, RELIEF, PRESSURE AND TEMPERATURE (FOR HOT WATER SUPPLY SYSTEMS) |
| MIL-E-22200-4 Revision D:1991 | ELECTRODES, WELDING, COVERED, COPPER-NICKEL ALLOY |
| MIL-C-3635 Revision C:1978 | COMPASS, DRAFTING, BEAM |
| ASTM F 96 : 1977 : R2005 | Standard Specification for Electronic Grade Alloys of Copper and Nickel in Wrought Forms |
| ASTM F 1387 : 1999 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
| ASTM F 375 : 1989 : R2010 | Standard Specification for Integrated Circuit Lead Frame Material |
| ASTM F 96 : 1977 : R1999 | Standard Specification for Electronic Grade Alloys of Copper and Nickel in Wrought Forms |
| MIL-DTL-32139 Revision B:2017 | Connectors, Electrical, Rectangular, Nanominiature, Polarized Shell, General Specification for |
| MIL-DTL-28754-62 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER, CROSSOVER, CONTACT TAILS ON .050 CENTERS |
| MIL-DTL-28748 Revision D:2001 | CONNECTOR, PLUG AND RECEPTACLE, RECTANGULAR, RACK AND PANEL SOLDER TYPE AND CRIMP TYPE CONTACTS - GENERAL SPECIFICATION FOR |
| MIL STD 11991 : A | GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES |
| MIL DTL 28754/60 : A | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS |
| MIL-DTL-11996 Revision C:2015 | HANDSETS, GENERAL SPECIFICATION FOR |
| MIL-DTL-28754-59 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS (CERAMIC COMPATIBLE) |
| MIL-C-83522-1 Revision F:2006 | CONNECTOR, PLUG, FIBER OPTIC, SINGLE TERMINUS, THREADED, (STEP-DOWN NOSE INTERFACE), LENSLESS, EPOXY, FOR 50/125 MICROMETER, 62.5/125 MICROMETER, AND 100/140 MICROMETER |
| MIL-C-83522-7 Revision C:2006 | CONNECTOR, RECEPTACLE, FIBER OPTIC, SINGLE TERMINUS, THREADED, PARALLEL PC MOUNT |
| MIL-DTL-83503-20 Revision D:2004 | Connectors, Electrical, Flat Cable, Nonenvironmental Header, Right Angle (.100 Spacing) with Polarizing Feature Solderless Wrappost or PWB Termination |
| MIL-DTL-28754 Revision E:2016 | Connectors, Electrical, Modular, and Component Parts General Specification for |
| ASTM F 375 : 1989 : R2015 | Standard Specification for Integrated Circuit Lead Frame Material |
| ASTM F 375 : 1989 : R2005 | Standard Specification for Integrated Circuit Lead Frame Material |
| ASME PV CODE 2C : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS |
| ASME B40.100 : 2013 | Pressure Gauges and Gauge Attachments (B40.100 - 2013) |
| MIL C 83503 : A | CONNECTOR, ELECTRICAL, FLAT CABLE, AND/OR PRINTED WIRING BOARD, NONENVIRONMENTAL GENERAL SPECIFICATION FOR |
| MIL C 15730 : M | COOLER, FLUID, NAVAL SHIPBOARD, LUBRICATING OIL, HYDRAULIC OIL, AND FRESH WATER |
| NNN-S-1356 Revision B:1978 | SPATULA LABORATORY (METAL BLADE) |
| MIL C 24712 : A | COATINGS, POWDER (METRIC) |
| MIL S 83734 : F | SOCKETS, PLUG-IN ELECTRONIC COMPONENTS, DUAL-IN-LINE PACKAGES (DIPS) & SINGLE-IN-LINE PACKAGES (SIPS), GENERAL SPECIFICATION FOR |
| ASTM B 248 : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
| ASTM F 1387 : 1999 : R2012 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
| ASTM F 375 : 1989 : R1999 | Standard Specification for Integrated Circuit Lead Frame Material |
| MIL-DTL-28754-47 Revision C:2015 | CONNECTORS, ELECTRICAL MODULAR, TYPE 4, CONNECTOR, 100 PIN, RIGHT ANGLE CONTACT TAILS ON .100 CENTERS |
| MIL-STD-186 Revision F:2002 | PROTECTIVE FINISHING SYSTEMS FOR ROCKETS, GUIDED MISSILES, SUPPORT EQUIPMENT AND RELATED MATERIALS |
| AWS A5.6/A5.6M : 2008 | SPECIFICATION FOR COPPER AND COPPER-ALLOY ELECTRODES FOR SHIELDED METAL ARC WELDING |
| MSS SP 119 : 2010 | FACTORY-MADE WROUGHT BELLED END PIPE FITTINGS FOR SOCKET-WELDING |
| DOD HDBK 270 : 0 | METALLIC MATERIALS, MAGNETIC PERMEABILITY AND ELECTRICAL CONDUCTIVITY, CHARACTERISTICS OF (METRIC) |
| MIL-C-83522-4 Revision F:2006 | CONNECTOR, RECEPTACLE, FIBER OPTIC, SINGLE TERMINUS, THREADED, RECEPTACLE, LOW PROFILE PARALLEL PC MOUNT |
| MIL-HDBK-270 Revision A:1991 | METALLIC MATERIALS FOR LOW MAGNETIC APPLICATIONS, MAGNETIC PERMEABILITY AND ELECTRICAL CONDUCTIVITY, CHARACTERISTICS OF (METRIC) |
| MIL-DTL-83503-24 Revision C:2004 | Connectors, Electrical, Flat Cable, Nonenvironmental Four Wall Header, Right Angle (.100 Spacing) with Polarizing Feature Solderless Wrappost or PWB Termination |
| GG-C-550 Revision B:1988 | COMPASS, DRAFTING, PIVOT, DROP SPRING BOW, PEN AND PENCIL, WITH CASE |
| GG-H-0080 Revision A:1967 | HANDLE AND BLADE SET, SURGICAL KNIFE, DETACHABLE BLADE |
| MIL-E-22200 Revision G:1989 | ELECTRODES, WELDING, COVERED: GENERAL SPECIFICATION FOR |
| MIL S 24749 : 0 | STRAPS, ELECTRICAL GROUNDING (METRIC) |
| MIL-STD-1276 Revision H:2013 | Leads for Electronic Component Parts |
| MIL-DTL-83503-21 Revision D:2004 | Connectors, Electrical, Flat Cable, Nonenvironmental, Header, Straight thru (.100 Inch Spacing) with Polarizing Feature Solderless Wrappost or PWB Termination |
| MIL C 28748 : B | CONNECTOR, ELECTRICAL, RECTANGULAR, RACK AND PANEL, SOLDER TYPE AND CRIMP TYPE CONTACTS, GENERAL SPECIFICATION FOR |
| MIL C 28754 : D | CONNECTOR, ELECTRICAL, MODULAR AND COMPONENT PARTS, GENERAL SPECIFICATION FOR |
| ASTM F 1387 : 1999 : R2005 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
| MIL-DTL-83503-25 Revision C:2004 | Connectors, Electrical, Flat Cable, Nonenvironmental Four Wall Header, Straight thru (.100 Spacing) with Polarizing Feature, Solderless Wrappost or PWB Termination |
| MIL-C-83522-3 Revision G:2006 | CONNECTOR, ADAPTER, FIBER OPTIC, BULKHEAD MOUNT, FOR SINGLE FIBER |
| MIL-C-83522-5 Revision E:2006 | CONNECTOR, RECEPTACLE, FIBER OPTIC, BULKHEAD MOUNT, FOR SINGLE FIBER |
| DSCC 86037 : B | CONNECTORS, RECEPTACLE, ELECTRICAL, LATCH HOUSINGS, CRIMP TO WIRE CONTACTS, GENERAL DRAWING FOR |
| SAE J461_201801 | Wrought and Cast Copper Alloys |
| ASTM F 96 : 1977 : R2015 | Standard Specification for Electronic Grade Alloys of Copper and Nickel in Wrought Forms |
| MIL-DTL-28754-61 Revision A:2016 | Connectors, Electrical, Modular, Type IV, Connector, 100 Pin, Center, Crossover, Contact Tails on .100 Centers (Ceramic Compatible) |
| MIL-C-28859 Revision B:1990 | CONNECTOR COMPONENT PART, ELECTRICAL BACK PLANE, PRINTED WIRING, GENERAL SPECIFICATION FOR |
| MIL-B-55252 Revision B:1992 | BATTERIES, NON-RECHARGEABLE, MAGNESIUM |
| ASTM B 248M : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
| MIL-C-83522-8 Revision C:2006 | CONNECTOR, RECEPTACLE, FIBER OPTIC, SINGLE TERMINUS, THREADED, BULKHEAD, HEX NUT MOUNT |
| MIL-C-83522-2 Revision G:2006 | CONNECTOR, PLUG, FIBER OPTIC, SINGLE TERMINUS, THREADED, (STRAIGHT NOSE INTERFACE), LENSLESS, EPOXY, FOR 50/125 MICROMETER, 62.5/125 MICROMETER, AND 100/140 MICROMETER |
| ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM B 846 : 2011-07 | TERMINOLOGY FOR COPPER AND COPPER ALLOYS |
| ASTM B 248M : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
| ASTM B 248 : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
| ASTM B 171/B171M : 2012-12 | SPECIFICATION FOR COPPER-ALLOY PLATE AND SHEET FOR PRESSURE VESSELS, CONDENSERS, AND HEAT EXCHANGERS |
| ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.