ASTM A 888 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
Hardcopy , PDF
28-01-2020
English
28-01-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
A 04
|
| DocumentType |
Standard
|
| Pages |
59
|
| ProductNote |
This standard is also refers to Fed. Std. No. 123.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.
1.2The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.
1.3This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the dimensions found in Tables 1 and 2 and all other applicable requirements given in this specification.2
1.3.1Lengths:
| Figures | |
| EDP/ASA Identification Numbers | Fig. 1 |
| 10 ft (3.0 m) in sizes and 5 ft. (1.5 m) | Fig. 1, Fig. 2 |
| Method of Specifying Fittings | Fig. 3 |
1.3.2Fittings:
| Quarter Bend | Fig. 5 |
| Quarter Bend, Reducing | Fig. 6 |
| Quarter Bend, with Side Opening | Fig. 7 |
| Quarter Bend, with Heel Opening | Fig. 8 |
| Quarter Bend, Tapped | Fig. 9 |
| Quarter Bend, Double | Fig. 10 |
| Quarter Bend, Long | Fig. 11 |
| Short Sweep | Fig. 12 |
| Long Sweep | Fig. 13 |
| Long Sweep, Reducing | Fig. 14 |
| Fifth Bend | Fig. 15 |
| Sixth Bend | Fig. 16 |
| Eighth Bend | Fig. 17 |
| Eighth Bend, Long | Fig. 18 |
| Sixteenth Bend | Fig. 19 |
| Sanitary Tee | Fig. 20 |
| Sanitary Tee with Side Opening | Fig. 21 |
| Sanitary Tee with 2 in. Side Opening R or L/R and L | Fig. 22 |
| Sanitary Tee, New Orleans Special with Side Opening | Fig. 23 |
| Sanitary Tee with 45° Side Openings and New Orleans | Fig. 24 |
| Sanitary Special Tee Tapped | Fig. 25 |
| Sanitary Tapped Tee, Horizontal Twin | Fig. 26 |
| Sanitary Tapped Tee, Double Vertical | Fig. 27 |
| Y Branch | Fig. 28 |
| Y Branch, Double | Fig. 29 |
| Y Branch, Upright | Fig. 30 |
| Upright Y Wide Center Florida Special | Fig. 31 |
| Y Branch, Combination 1/8Bend | Fig. 32 |
| Y Branch, Combination 1/8Bend Double | Fig. 33 |
| Sanitary Cross | Fig. 34 |
| Sanitary Cross with Side Opening | Fig. 35 |
| Sanitary Cross, New Orleans, with Side Openings | Fig. 36 |
| Sanitary Cross, New Orleans, with 45° Special and | Fig. 37 |
| Sanitary Cross, Tapped | Fig. 38 |
| Test Tee | Fig. 39 |
| Tapped Extension Piece | Fig. 40 |
| Increaser-Reducer | Fig. 41 |
| Increaser-Reducer, Short | Fig. 42 |
| Tapped Adapter | Fig. 43 |
| Blind Plug | Fig. 44 |
| Iron Body Cleanout, Tapped | Fig. 45 |
| P Trap | Fig. 46 |
| P Trap, Long | Fig. 47 |
| P Trap, Deep Seal | Fig. 48 |
| P Trap, with Primer | Fig. 49 |
| P Trap, with Tapped Inlet | Fig. 50 |
| Tapped Inlet, Double | Fig. 51 |
| Modified Combination Wye and 1/8 Bend, Double | Fig. 52 |
| Modified Combination Wye and 1/8 Bend, Double, Extended | Fig. 53 |
| Two-Way Cleanout | Fig. 54 |
| Twin Cleanout | Fig. 55 |
| Closet Bend, Regular and Reducing | Fig. 56 |
| Closet Flange Riser | Fig. 57 |
| Tapping Bosses | Fig. 58 |
| Double Sweep Sanitary Tee (Extended) | Fig. 59 |
| Running Trap with Double Vents | Fig. 60 |
| P Trap with Tapped or Hubless Side Inlet | Fig. 61 |
| Vented Tub Wye Extended, Double | Fig. 62 |
| Vented Tub Wye Extended Offset, Left or Right | Fig. 63 |
| Vented Tub Wye | Fig. 64 |
| Double Two-Way Cleanout | Fig. 65 |
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301.
Note 1:The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1277 : 2020 | Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings |
| ASTM C 1540 : 2020 | Standard Specification for Heavy-Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings |
| ASTM A 1111 : 2018 | Standard Specification for Cast Iron Closet Flanges for Use With Cast Iron Soil Pipe and Fittings in Gravity Flow Plumbing Drain, Waste, and Vent Sanitary Applications |
| ASTM A 1056 : 2020 | Standard Specification for Cast Iron Couplings Used for Joining Hubless Cast Iron Soil Pipe and Fittings |
| ASTM E 8/E8M : 2016 : REV A : EDT 1 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM A 644 : 1998 | Standard Terminology Relating to Iron Castings |
| ASTM D 3960 : 1998 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.