ASTM A 829/A829M : 2017
Current
The latest, up-to-date edition.
Standard Specification for Alloy Structural Steel Plates
Hardcopy , PDF
English
15-03-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This specification covers structural quality alloy steel plates.
| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers structural quality alloy steel plates.
1.2The plates are usually specified to chemical composition requirements, but tensile properties may also be specified.
1.2.1When tensile properties are required, the specific requirements must be compatible with the chemical composition, condition, and plate thickness.
1.3The plates are available in the following five conditions:
1.3.1Condition AR—As rolled (hot rolled),
1.3.2Condition A—Annealed,
1.3.3Condition N—Normalized,
1.3.4Condition NT—Normalized and tempered, and
1.3.5Condition QT—Quenched and tempered.
1.4The plates are available in the following three forms:
1.4.1Form I—Rectangular,
1.4.2Form II—Circular and semi-circular, and
1.4.3Form III—Sketch, including rings.
1.5The plates are available in the following five edge categories:
1.5.1Edge 1—Mill edge,
1.5.2Edge 2—Universal mill edge,
1.5.3Edge 3—Sheared edge,
1.5.4Edge 4—Gas cut edge, and
1.5.5Edge 5—Special cut edge.
1.6The plates are available in the following seven finishes:
1.6.1Finish 1—As rolled (hot rolled),
1.6.2Finish 2—Blast cleaned,
1.6.3Finish 3—Blast cleaned and oiled,
1.6.4Finish 4—Pickled,
1.6.5Finish 5—Pickled and oiled,
1.6.6Finish 6—Painted, one prime coat, and
1.6.7Finish 7—Painted, one prime coat and one finish coat.
1.6.8The plates are usually specified to have Finish 1.
1.7Supplementary requirements are provided for additional requirements that may be specified on the order.
1.8When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.
1.9The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.10This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 6/A6M : 2022 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM A 6/A6M : 2024 : REV A | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM A 6/A6M : 2024 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM A 6/A6M : 2023 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM A 6/A6M : 2021 | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
| ASTM A 6/A6M : 2024 : REV B | Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.