ASTM A 765/A765M : 2007 : R2022
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements
Hardcopy , PDF
02-09-2024
English
01-09-2022
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification2 covers heat-treated carbon steel and alloy steel forgings with mandatory toughness requirements. These forgings are intended for pressure vessels, feedwater heaters, and similar uses.
1.2These forgings include tube sheets, covers, channel barrels, integral forged channels, rings, nozzles, flanges, and similar parts.
1.3All grades are considered weldable under proper conditions.
1.4The maximum thickness of forgings produced to this specification is limited only by the capacity of the selected grade to respond to any heat treatment specified and to meet the specified mechanical tests, including impact tests at the specified temperature.
1.5Material supplied to this specification shall conform to the requirements of Specification A788/A788M, which outlines additional ordering information, manufacturing requirements, testing and retesting methods and procedures, marking, certification, product analysis variations, and additional supplementary requirements.
1.6If the requirements of this specification are in conflict with the requirements of Specification A788/A788M, the requirements of this specification shall prevail.
1.7The values stated in either inch-pound units or SI [metric] units are to be regarded separately as standard; within the text and tables, the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.8Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.
1.9This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A 788/A788M : 2022 | Standard Specification for Steel Forgings, General Requirements |
ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 788/A788M : 2022 | Standard Specification for Steel Forgings, General Requirements |
ASTM A 788/A788M : 2023 | Standard Specification for Steel Forgings, General Requirements |
ASTM A 788/A788M : 2024 | Standard Specification for Steel Forgings, General Requirements |
ASTM E 165/E165M : 2023 | Standard Practice for Liquid Penetrant Testing for General Industry |
ASTM A 275/A275M : 2018 | Standard Practice for Magnetic Particle Examination of Steel Forgings |
ASTM A 275/A275M : 2023 | Standard Practice for Magnetic Particle Examination of Steel Forgings |
ASTM A 370 : 2023 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 388/A388M : 2023 | Standard Practice for Ultrasonic Examination of Steel Forgings |
ASTM A 275/A275M : 2018 : R2023 | Standard Practice for Magnetic Particle Examination of Steel Forgings |
ASTM A 788/A788M : 2022 : REV A | Standard Specification for Steel Forgings, General Requirements |
ASTM E 112 : 2013 : R2021 | Standard Test Methods for Determining Average Grain Size |
ASTM A 388/A388M :2019 | Standard Practice for Ultrasonic Examination of Steel Forgings |
ASTM E 112 : 2024 | Standard Test Methods for Determining Average Grain Size |
ASTM E 165/E165M : 2018 | Standard Practice for Liquid Penetrant Testing for General Industry |
ASTM A 370 : 2024 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.