ASTM A 500/A500M : 2021 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes
Hardcopy , PDF
24-11-2023
English
20-09-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special structural tubular shapes for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes.
1.2This tubing is produced in both welded and seamless sizes with a periphery of 88 in. [2235 mm] or less, and a specified wall thickness of 1.000 in. [25.4 mm] or less. Grade D requires heat treatment.
Note 1:Products manufactured to this specification may not be suitable for those applications such as dynamically loaded elements in welded structures, etc., where low-temperature notch-toughness properties, which are typically measured by Charpy Impact testing, may be important. There are other ASTM standards that do have CVN requirements and may be more suitable for those applications.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
1.4The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 1057/A1057M : 2008 : R2019 | Standard Specification for Steel, Structural Tubing, Cold Formed, Welded, Carbon, Zinc-Coated (Galvanized) by the Hot-Dip Process |
| ASTM E 2950 : 2014 : R2020 | Standard Specification for Metal Canopy Systems |
| ASTM C 1802 : 2020 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
| ASTM A 1076/A1076M : 2020 | Standard Specification for Cold Formed Carbon Structural Steel Tubing Made from Metallic Precoated Sheet Steel |
| ASTM C 1802 : 2023 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
| ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2023 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 941 : 2022 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 751 : 2021 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM A 370 : 2020 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 370 : 2023 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2022 : REV A | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 751 : 2020 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2018 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.