ASTM A 276/A276M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Stainless Steel Bars and Shapes
Hardcopy , PDF
15-01-2024
English
21-03-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This specification covers hot-finished or cold-finished bars except bars for reforging (Note 1).
| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers hot-finished or cold-finished bars except bars for reforging (Note 1). It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The free-machining types (Note 2) for general corrosion resistance and high-temperature service are covered in a separate specification.
Note 1:For bars for reforging, see Specification A314.
Note 2:For free-machining stainless bars designed especially for optimum machinability, see Specification A582/A582M.
Note 3:There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol. 02.04.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
| ASTM A 1069/A1069M : 2019 | Standard Specification for Laser and Laser Hybrid Welded Stainless Steel Bars, Plates, and Shapes |
| ASTM F 2854 : 2021 | Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing |
| ASTM A 1040 : 2017 : R2022 | Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels |
| ASTM F 1807 : 2023 | Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM F 2929 : 2017 : R2021 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| ASTM A 484/A484M : 2023 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM D 7027 : 2020 | Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine |
| ASTM D 6783 : 2005 : REV A : R2022 | Standard Specification for Polymer Concrete Pipe |
| ANSI/AWWA C509:2023 | Resilient-Seated Gate Valves for Water Supply Service |
| ASTM G 32 : 2016 : R2021 : EDT 1 | Standard Test Method for Cavitation Erosion Using Vibratory Apparatus |
| ASTM G 134 : 2017 : R2023 | Standard Test Method for Erosion of Solid Materials by Cavitating Liquid Jet |
| ASTM C 341/C341M : 2018 | Standard Practice for Preparation and Conditioning of Cast, Drilled, or Sawed Specimens of Hydraulic-Cement Mortar and Concrete Used for Length Change Measurements |
| ASTM A 194/A194M : 2023 | Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
| ASTM F 2080 : 2023 | Standard Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe and SDR9 Polyethylene of Raised Temperature (PE-RT) Pipe |
| ASTM C 1802 : 2023 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures |
| ASTM F 3184 : 2016 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM A 1082/A1082M : 2016 : R2021 | Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications |
| ANSI/AWWA C530:2017 | Pilot-Operated Control Valves |
| ANSI/MSS SP-58:2018 | PIPE HANGERS AND SUPPORTS Materials, Design, Manufacture, Selection, Application, and Installation (ANSI-approved American National Standard) |
| ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 1058 : 2014 | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 582/A582M : 2021 | Standard Specification for Free-Machining Stainless Steel Bars |
| ASTM A 1058 : 2012 : REV A | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 484/A484M : 2023 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM A 1058 : 2019 | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 484/A484M : 2021 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| AS 1528.4:2019 | Stainless steel tubes and tube fittings for food processing and hygienic applications Clamp tube fittings |
| ASTM A 1058 : 2008 | Standard Test Methods for Mechanical Testing of Steel Products<span class='unicode'>—</span>Metric |
| AS 4793:2020 | Mechanical tapping bands for waterworks purposes |
| ASTM A 582/A582M : 2022 | Standard Specification for Free-Machining Stainless Steel Bars |
| ASTM A 314 : 1997 | Standard Specification for Stainless Steel Billets and Bars for Forging |
| ASTM A 751 : 2021 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM A 370 : 2020 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 1058 : 2012 | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 1058 : 2012 : REV B | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
| ASTM A 582/A582M : 2012 : R2017 | Standard Specification for Free-Machining Stainless Steel Bars |
| AS 1528.2:2019 | Stainless steel tubes and tube fittings for food processing and hygienic applications Screwed tube couplings |
| ASTM A 484/A484M : 2022 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM A 751 : 2020 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM A 370 : 2011 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| AS 3996:2019 | Access covers and grates |
| ASTM A 1058 : 2009 | Standard Test Methods for Mechanical Testing of Steel Products<char: emdash>Metric |
| ASTM A 582/A582M : 1995 : REV B | Standard Specification for Free-Machining Stainless Steel Bars |
| ASTM A 484/A484M : 2020 : REV B | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.