ASTM A 1096/A1096M : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluating Bond of Individual Steel Wire, Indented or Plain, for Concrete Reinforcement
Hardcopy , PDF
23-08-2022
English
24-11-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 01.04, 2018 Specifies procedures for evaluating bond of individual steel wire, indented or plain, for concrete reinforcement.
| Committee |
A 01
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method describes procedures for evaluating bond of individual steel wire, indented or plain, for concrete reinforcement. The bond determined by this test method is stated as the tensile force needed to pull the wire through the cured mortar in a cylindrical steel casing.
1.2The result of the test is the maximum tensile force measured on the loaded end of the wire recorded at a free-end slip less than or equal to 0.10 in. [2.5 mm].
1.3Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 511 : 2021 | Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 150/C150M : 2017-04 | SPECIFICATION FOR PORTLAND CEMENT |
| ASTM C 192/C192M : 2000 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 511 : 2019 | Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes |
| ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
| ASTM C 192/C192M : 2016-04 | PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY |
| ASTM C 778 : 2017 | Standard Specification for Standard Sand |
| ASTM C 778 : 2017 : REDLINE | Standard Specification for Standard Sand |
| ASTM A 421/A421M : 2015 : REDLINE | Standard Specification for Stress-Relieved Steel Wire for Prestressed Concrete |
| ASTM A 421/A421M : 2015 | Standard Specification for Stress-Relieved Steel Wire for Prestressed Concrete |
| ASTM C 150/C150M : 2020 | Standard Specification for Portland Cement |
| ASTM A 421/A421M : 2021 | Standard Specification for Stress-Relieved Steel Wire for Prestressed Concrete |
| ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
| ASTM C 778 : 2021 | Standard Specification for Standard Sand |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.