ASTM A 1083/A1083M : 2012 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, Produced by Twin-Roll Casting Process
Hardcopy , PDF
24-11-2023
English
07-09-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 01.03, 2017 Specifies cold-rolled, carbon, structural, and high-strength low-alloy, in coils and cut lengths produced by the twin-roll casting process.
| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers cold-rolled, carbon, structural, and high-strength low-alloy, in coils and cut lengths produced by the twin-roll casting process.
1.2Cold rolled steel sheet produced by the twin-roll casting process is available in the designations as listed in 4.1.
1.3This specification does not apply to steel strip as described in Specification A109/A109M.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2023 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM E 18 : 2020 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM A 941 : 2022 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 370 : 2020 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 370 : 2023 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2022 : REV A | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 370 : 2011 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM E 18 : 2019 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM A 941 : 2009 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASTM A 109/A109M : 1998 : REV A | Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled |
| ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM E 517 : 2000 : R2006 | Standard Test Method for Plastic Strain Ratio r for Sheet Metal |
| ASTM A 941 : 2018 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.