ASTM A 1053/A1053M : 2012 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Welded Ferritic-Martensitic Stainless Steel Pipe
Hardcopy , PDF
29-04-2022
English
02-10-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 01.01, 2017 Defines seam welded ferritic-martensitic (dual phase) stainless steel pipe intended for abrasive and general corrosion service, manufactured with or without the addition of filler metal.
| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers seam welded ferritic-martensitic (dual phase) stainless steel pipe intended for abrasive and general corrosion service, manufactured with or without the addition of filler metal. Nominal sizes are NPS 2 to NPS 36 inclusive, with nominal (average) wall thickness up to 0.75-in. (19 mm).
1.2The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents. Therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation is specified in the order.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 1016/A1016M : 2002 | Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes |
| SAE J 1086 : 2012 | NUMBERING METALS AND ALLOYS |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| ASTM A 941 : 2022 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASME B36.10 : 1979 | WELDED AND SEAMLESS WROUGHT STEEL PIPE |
| ASTM A 370 : 2020 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM A 370 : 2011 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ASTM A 941 : 2009 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
| ASME B36.19 : 1976 | STAINLESS STEEL PIPE |
| ASTM A 941 : 2018 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.